Manuals / REI / Kitchen Appliance / Ventilation Hood

REI manual MDC-2100/MDC-900, Viewing Bands 1, 2 and, Press F4/MDC Anlz, Press SWEEP/ANALYZE

Models: MDC-900

1 16

Download 16 pages 63.82 Kb

Specs Signal identification Process

Page 7

Image 7

Page 6 Page 8

Page 7

Image 7

REI manual MDC-2100/MDC-900, Viewing Bands 1, 2 and, Press F4/MDC Anlz, Press SWEEP/ANALYZE, Press F4/Identify see B

Page 6 Page 8

Our partner
Обсуждение вопроса Почему люди покупают большой RAM в Европу? из чата Гаражний кооператив "Мюнхен" 🇺🇦, Мюнхен, Германия
English grammar trainer

iOS Android Choose grammars and practice

Related pages CHAPTER 6 TROUBLESHOOTING for True Fitness CS800 Specifications for Panasonic PT-D12000E Error messages for Panasonic AJ-HD1700 Flowchart 2.13-No OS Loading, Diskette Drive for HP NX9500 Check for Pending Printer Data When Idle For / Reverse Data for Intermate 100 Battery installation for Acer SV-200 Caster Assembly Parts List for Powermatic 2700 Programming Cable Box Using Code Lists for GE RM94948 Contents for Gefen EXT-HDMI-844 Multifunctional settings for 3M X55I To use the directed netboot feature for Nortel Networks Passport ARN Routers Are there any specific symbols to be aware of in the Rinnai E110CN manual?

Contents

RESEARCH ELECTRONICS INTERNATIONAL 455 Security Drive MDC-2100/MDC-900MDC-900 MDC-2100 OWNER’S GUIDE FIGURE 11 ANALYZE MODE USING THE MDC OSCOR TABLE of CONTENTSTABLE of FIGURES STORING A SIGNAL IN THE MDC FREQUENCY RANGE Figure 1 MDC-2100 MICROWAVE DOWNCONVERTER INTRODUCTION Filter A & B ANTENNA BANDFilter A Filter B Installing the MDC-2100/MDC-900 Operational Control of the MDC-2100/MDC-900 Signal identification ProcessOSCOR Version Press F4/Identify see Figure 6B Viewing Bands 1, 2 andPress F4/MDC Anlz Press SWEEP/ANALYZE FIGURE 7 USING “IDENTIFY” TO VERIFY A SIGNAL OSCOR OSCOR Sweep and Analyze Modes with the MDCFigure 6A ANALYZING AN MDC SIGNAL OSCOR Figure 6B ANALYZING AN MDC SIGNAL OSCOR Figure 8 SELECTING A SIGNAL WITH THE MDC OSCOR Storing a Sweep Span with the MDC Span Storing a Signal in the MDC Frequency RangeExample of a Desired Frequency Recommended Implementation Microwave Transmission Considerations for the MDC it is absolutely necessary in order to save time. A good rule of thumb is to assume that the MDC has an antenna pattern that is about 100 degrees wide. In other words, it is necessary to point the MDC in at least 4 different directions around the room to cover the perimeter. Also, the MDC should be pointed up and possibly moved around the room to cover the ceiling, and down to cover the floor. Furthermore, if you expect a very sophisticated threat, it is recommended to point the MDC into ducting, above ceiling tiles, and in any enclosed spaces in which it would be possible to place a transmitter with a high gain antenna. It is highly recommended that the “Show All” mode of operation for the MDC-2100 be utilized MDCA-all and MDCB-all if using OSCOR 5.0. When a signal is detected, the user can then manually select the different antenna bands and filters to further investigate the signal. Or, the user can simply go to the analyze mode and allow the MDC to determine the operational frequency of the transmitter. Also, it is not recommended to use the MDC with the OSCOR automatic mode unless the MDC directional characteristics are taken into consideration. If running the OSCOR and MDC in the automatic mode, take care to enable the appropriate MDC spans. To maximize usage of the MDC, include MDC 3-21GHz Filter A and MDC 3-21GHz Filter B in your span list For OSCOR 4.0 users, set span to All Bands A&B Using the MTU-2100 Microwave Test Unit MDC-900 MDC-2100/MDC-900 SPECIFICATIONSSpecifications MDC-2100 Technical Bulletin