Manuals / REI / Kitchen Appliance / Ventilation Hood

REI manual Introduction, MDC-2100/MDC-900, MDC-2100 MICROWAVE DOWNCONVERTER

Models: MDC-900

1 16

Download 16 pages 63.82 Kb

Specification Signal identification Process

Page 3

Image 3

Page 2 Page 4

Page 3

Image 3

REI manual Introduction, MDC-2100/MDC-900, MDC-2100 MICROWAVE DOWNCONVERTER

Page 2 Page 4

Our partner
Обсуждение вопроса Почему люди покупают большой RAM в Европу? из чата Гаражний кооператив "Мюнхен" 🇺🇦, Мюнхен, Германия

Related pages Troubleshooting for Vanguard VE36L Product Specifications Operating Environment for Asante Technologies FS5016 Index of Error Messages for Acer 2420 Power Level Chart for Whirlpool MCE04XW Problèmes dinstallation for Samsung LS19CMYKFZ/EN Parts list for Zenoah CHT2301, HT2301 Code List for Jasco RM94903 General Service for Weed Eater HD13538 Limited Warranty of Bosch Portable and Benchtop Power Tools for Bosch Power Tools FNA250-15 How often should I check the safety speed PS19B and PS24B settings?

Contents

RESEARCH ELECTRONICS INTERNATIONAL 455 Security Drive MDC-2100/MDC-900MDC-900 MDC-2100 OWNER’S GUIDE FIGURE 11 ANALYZE MODE USING THE MDC OSCOR TABLE of CONTENTSTABLE of FIGURES STORING A SIGNAL IN THE MDC FREQUENCY RANGE Figure 1 MDC-2100 MICROWAVE DOWNCONVERTER INTRODUCTION Filter A & B ANTENNA BANDFilter A Filter B Installing the MDC-2100/MDC-900 Signal identification Process Operational Control of the MDC-2100/MDC-900OSCOR Version Press F4/Identify see Figure 6B Viewing Bands 1, 2 andPress F4/MDC Anlz Press SWEEP/ANALYZE FIGURE 7 USING “IDENTIFY” TO VERIFY A SIGNAL OSCOR OSCOR Sweep and Analyze Modes with the MDCFigure 6A ANALYZING AN MDC SIGNAL OSCOR Figure 6B ANALYZING AN MDC SIGNAL OSCOR Figure 8 SELECTING A SIGNAL WITH THE MDC OSCOR Storing a Sweep Span with the MDC Span Storing a Signal in the MDC Frequency RangeExample of a Desired Frequency Recommended Implementation Microwave Transmission Considerations for the MDC it is absolutely necessary in order to save time. A good rule of thumb is to assume that the MDC has an antenna pattern that is about 100 degrees wide. In other words, it is necessary to point the MDC in at least 4 different directions around the room to cover the perimeter. Also, the MDC should be pointed up and possibly moved around the room to cover the ceiling, and down to cover the floor. Furthermore, if you expect a very sophisticated threat, it is recommended to point the MDC into ducting, above ceiling tiles, and in any enclosed spaces in which it would be possible to place a transmitter with a high gain antenna. It is highly recommended that the “Show All” mode of operation for the MDC-2100 be utilized MDCA-all and MDCB-all if using OSCOR 5.0. When a signal is detected, the user can then manually select the different antenna bands and filters to further investigate the signal. Or, the user can simply go to the analyze mode and allow the MDC to determine the operational frequency of the transmitter. Also, it is not recommended to use the MDC with the OSCOR automatic mode unless the MDC directional characteristics are taken into consideration. If running the OSCOR and MDC in the automatic mode, take care to enable the appropriate MDC spans. To maximize usage of the MDC, include MDC 3-21GHz Filter A and MDC 3-21GHz Filter B in your span list For OSCOR 4.0 users, set span to All Bands A&B Using the MTU-2100 Microwave Test Unit MDC-900 MDC-2100/MDC-900 SPECIFICATIONSSpecifications MDC-2100 Technical Bulletin