Manuals / REI / Kitchen Appliance / Ventilation Hood

REI manual Installing the MDC-2100/MDC-900

Models: MDC-900

1 16

Download 16 pages 63.82 Kb

Specifications Signal identification Process

Page 5

Image 5

Image 5

REI manual Installing the MDC-2100/MDC-900

Our partner
Обсуждение вопроса Почему люди покупают большой RAM в Европу? из чата Гаражний кооператив "Мюнхен" 🇺🇦, Мюнхен, Германия

Related pages All Install page 15. Removing and Installing an iDRAC6 Enterprise Card for Dell R210 II Rapidamente Installi for Rockford Fosgate T400-2 Wall Mounting Installation for Amcor AMH8 Installation for Samsung LTN325W REMOVING/INSTALLING the Floor Basket Figure for Invacare LYNX LX-3PLUS 4. Installation for Barco 26-0702000-00 Installing Optional ATTACH- Ments for Poulan 545186799 Installation of the CPU and Heatsink for Gigabyte GA-8I915P-MF Installation for Electrolux 726659 Winding/Installing the Bobbin for Brother 885-S61 What are the safety features mentioned in Kenmore oven instructions?(#)

Contents

MDC-900 MDC-2100 MDC-2100/MDC-900OWNER’S GUIDE RESEARCH ELECTRONICS INTERNATIONAL 455 Security Drive TABLE of FIGURES TABLE of CONTENTSSTORING A SIGNAL IN THE MDC FREQUENCY RANGE FIGURE 11 ANALYZE MODE USING THE MDC OSCOR Figure 1 MDC-2100 MICROWAVE DOWNCONVERTER INTRODUCTION Filter A ANTENNA BANDFilter B Filter A & B Installing the MDC-2100/MDC-900 OSCOR Version Signal identification ProcessOperational Control of the MDC-2100/MDC-900 Press F4/MDC Anlz Viewing Bands 1, 2 andPress SWEEP/ANALYZE Press F4/Identify see Figure 6B Figure 6A ANALYZING AN MDC SIGNAL OSCOR OSCOR Sweep and Analyze Modes with the MDCFigure 6B ANALYZING AN MDC SIGNAL OSCOR FIGURE 7 USING “IDENTIFY” TO VERIFY A SIGNAL OSCOR Figure 8 SELECTING A SIGNAL WITH THE MDC OSCOR Storing a Sweep Span with the MDC Example of a Desired Frequency Storing a Signal in the MDC Frequency RangeRecommended Implementation Span Microwave Transmission Considerations for the MDC it is absolutely necessary in order to save time. A good rule of thumb is to assume that the MDC has an antenna pattern that is about 100 degrees wide. In other words, it is necessary to point the MDC in at least 4 different directions around the room to cover the perimeter. Also, the MDC should be pointed up and possibly moved around the room to cover the ceiling, and down to cover the floor. Furthermore, if you expect a very sophisticated threat, it is recommended to point the MDC into ducting, above ceiling tiles, and in any enclosed spaces in which it would be possible to place a transmitter with a high gain antenna. It is highly recommended that the “Show All” mode of operation for the MDC-2100 be utilized MDCA-all and MDCB-all if using OSCOR 5.0. When a signal is detected, the user can then manually select the different antenna bands and filters to further investigate the signal. Or, the user can simply go to the analyze mode and allow the MDC to determine the operational frequency of the transmitter. Also, it is not recommended to use the MDC with the OSCOR automatic mode unless the MDC directional characteristics are taken into consideration. If running the OSCOR and MDC in the automatic mode, take care to enable the appropriate MDC spans. To maximize usage of the MDC, include MDC 3-21GHz Filter A and MDC 3-21GHz Filter B in your span list For OSCOR 4.0 users, set span to All Bands A&B Using the MTU-2100 Microwave Test Unit Specifications MDC-2100/MDC-900 SPECIFICATIONSMDC-2100 MDC-900 Technical Bulletin

Top Page Image Contents