8.Clean the area around the element opening. Remove any sediment from or around the element opening and inside the tank.

9.If you are cleaning the element you have removed, do so by scraping or soaking in vinegar or a deliming solution.

NOTE: Replacement elements must (1) be the same voltage and (2) no greater wattage than listed on the model rating plate affixed to the water heater.

10.A new gasket should be used in all cases to prevent a possible water leak. Place the new element gasket on the threaded side of the cleaned or new element and screw into tank, securing tightly using an element wrench.

FIGURE 20.

11.Close the water heater drain valve by turning the handle to the right (clockwise). The drain valve is on the lower front of the water heater.

12.Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

13.To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

14.Check element for water leaks. If leakage occurs, tighten element or repeat Steps 2 and 3, remove element and reposition gasket. Then repeat Steps 10 through 14.

15.Reconnect the two wires to the element and then check to make sure the thermostat remains firmly against the surface of the tank.

16.Replace terminal cover on thermostat making sure the locking tabs on the terminal cover are in place.

17.Fold back the insulation so that it covers the thermostat and element.

18.Replace outer door.

19.Turn “ON” electric power to water heater.

FIGURE 22.

DRAIN VALVE WASHER REPLACEMENT

(See Figure 23)

1.Follow “Draining” instructions.

2.Turning counter clockwise ( ), remove the hex cap below the screw handle.

3.Remove the washer and put the new one in place.

4.Screw the handle and cap assembly back into the drain valve and retighten using a wrench. DO NOT OVER TIGHTEN.

5.Follow instructions in the “Filling The Water Heater” section.

6.Check for leaks.

FIGURE 23.

 

SERVICE

 

If a condition persists or you are uncertain about the operation of the

 

water heater contact a service agency.

 

Use this guide to check a “Leaking” water heater. Many suspected

 

“Leakers” are not leaking tanks. Often the source of the water can be

 

found and corrected.

 

If you are not thoroughly familiar with your water heater and safety

FIGURE 21.

practices, contact a qualified installer to check the water heater.

16

Page 15 Page 17
Page 16
Image 16
Reliance Water Heaters 184735-000 instruction manual Drain Valve Washer Replacement, Service
Page 15 Page 17

184735-000 specifications

Reliance Water Heaters has established itself as a trusted name in the water heating industry, and the model 184735-000 is a testament to their commitment to delivering quality and efficiency. This water heater is designed to meet the needs of both residential and commercial users, providing reliable hot water supply for various applications.

One of the standout features of the Reliance 184735-000 is its significant storage capacity. With a tank that typically accommodates around 40 gallons, this model is ideal for households with moderate to high hot water usage. This capacity ensures that there is always enough hot water available for daily activities such as showering, washing dishes, and laundry.

The design of the Reliance 184735-000 incorporates advanced insulation technology, which minimizes heat loss. This feature enhances energy efficiency, allowing users to save on energy bills while ensuring optimal performance. The high-density foam insulation wrapped around the tank effectively reduces standby heat loss, making it an environmentally friendly choice.

Another notable characteristic of the 184735-000 is its user-friendly thermostat control. The intuitive dial allows users to easily adjust the water temperature according to preference and needs. This level of customization ensures comfort in hot water usage, whether for a relaxing bath or quick dishwashing.

The unit is also equipped with safety features such as a temperature and pressure relief valve. This mechanism releases excess pressure to prevent potential hazards, making it a reliable choice for peace of mind.

Reliance Water Heaters incorporates high-quality materials in the construction of the 184735-000. The tank is typically made of durable stainless steel or glass-lined steel, offering resistance against corrosion and extending the lifespan of the heater. Additionally, the heating elements are designed for efficient performance, ensuring rapid heating of water when required.

Installation of the Reliance 184735-000 is straightforward, with compatibility for various plumbing configurations. This versatility makes it a preferred option among homeowners and contractors alike.

In summary, the Reliance Water Heaters model 184735-000 combines efficiency, safety, and convenience. With its substantial storage capacity, energy-efficient design, and high-quality construction, it stands out as an excellent choice for anyone in need of a dependable water heating solution. Its user-friendly features further enhance its appeal, making it a noteworthy investment for reliable hot water availability.
Top Page Image Contents