Never obstruct the flow of ventilation air. If you have any doubts or questions at all, call your gas supplier. Failure to provide the proper amount of combustion air can result in a fire or explosion and cause property damage, serious bodily injury or death.

Unconfined Space

An Unconfined Space is one whose volume IS NOT LESS THAN 50 cubic feet per 1,000 Btu/hr (4.8 cubic meters per kW) of the total input rating of all appliances installed in the space. Rooms communicating directly with the space, in which the appliances are installed, through openings not furnished with doors, are considered a part of the unconfined space.

Makeup air requirements for the operation of exhaust fans, kitchen ventilation systems, clothes dryers and fireplaces shall also be considered in determining the adequacy of a space to provide combustion, ventilation and dilution air.

Unusually Tight Construction

In unconfined spaces in buildings, infiltration may be adequate to provide air for combustion, ventilation and dilution of flue gases. However, in buildings of unusually tight construction (for example, weather stripping, heavily insulated, caulked, vapor barrier, etc.) additional air must be provided using the methods described in the Confined Space section that follows.

Confined Space

A Confined Space is one whose volume IS LESS THAN 50 cubic feet per 1,000 Btu/hr (4.8 cubic meters per kW) of the total input rating of all appliances installed in the space.

Openings must be installed to provide fresh air for combustion, ventilation and dilution in confined spaces. The required size for the openings is dependent on the method used to provide fresh air to the confined space AND the total Btu/hr input rating of all appliances installed in the space.

Exhaust Fans

Where exhaust fans are installed, additional air shall be provided to replace the exhausted air. When an exhaust fan is installed in the same space with a water heater, sufficient openings to provide fresh air must be provided that accommodate the requirements for all appliances in the room and the exhaust fan. Undersized openings will cause air to be drawn into the room

through the water heater’s vent system causing poor combustion. Sooting, serious damage to the water heater and the risk of fire or explosion may result. It can also create a risk of asphyxiation.

Louvers and Grilles

The free areas of the fresh air openings in the instructions that follow do not take in to account the presence of louvers, grilles or screens in the openings.

The required size of openings for combustion, ventilation and dilution air shall be based on the “net free area” of each opening. Where the free area through a design of louver or grille or screen is known, it shall be used in calculating the size of opening required to provide the free area specified. Where the louver and grille design and free area are not known, it shall be assumed that wood louvers will have 25% free area and metal louvers and grilles will have 75% free area. Non motorized louvers and grilles shall be fixed in the open position.

Vent Adapter

The D85500NE/D85500PE model is shipped with a 6" to 8" diameter vent adapter (Fig. 11). The vent adapter fits on top of the installed blower exhaust. Use only vent adapters supplied with the unit. The venting must comply with the NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54 and for Canadian installations consult the Canadian Installation Code CAN/CSA B149.1-00.

Figure 11

vENTING INSTALLATION

Venting

THE INSTRUCTIONS IN THIS SECTION ON VENTING MUST BE FOLLOWED TO AVOID CHOKED COMBUSTION OR RECIRCULATION OF FLUE GASES. SUCH CONDITIONS CAUSE SOOTING OR RISKS OF FIRE AND ASPHYXIATION.

Heater must be protected from freezing downdrafts.

Remove all soot or other obstructions from the chimney that will retard a free draft.

Type B venting is recommended with these heaters. For typical venting application see TECHNICAL DATA VENTING on page 18.

This water heater must be vented in compliance with all local codes, the current revision of the National Fuel Gas Code (ANSI-Z223.1) and with the Category I Venting Tables.

If any part of the vent system is exposed to ambient temperatures below 40°F it must be insulated to prevent condensation.

•Do not connect the heater to a common vent or chimney with solid fuel burning equipment. This practice is prohibited by many local building codes as is the practice of venting gas fired equipment to the duct work of ventilation systems.

FIGURE 12

•Where a separate vent connection is not available and the vent pipe from the heater must be connected to a common

15

Page 14 Page 16
Page 15
Image 15
Reliance Water Heaters D85500PE, D85500NE VENTING Installation, Unconfined Space, Confined Space, Vent Adapter, Venting
Page 14 Page 16

D85500PE, D85500NE specifications

Reliance Water Heaters offers a diverse range of high-performance water heaters, with the D85500NE and D85500PE models standing out for their exceptional features and innovative technologies. Designed to meet the needs of modern households, these water heaters are engineered for efficiency, reliability, and ease of use.

The D85500NE is a natural gas water heater that boasts a 50-gallon capacity, making it an excellent choice for medium to large households. One of its main features is the Energy Factor (EF) rating, which ensures efficient operation and reduces energy costs. With a recovery rate of approximately 41 gallons per hour, it's capable of delivering a steady supply of hot water without delays, ensuring that families can enjoy uninterrupted use during peak demands.

The D85500PE model, on the other hand, operates using propane, catering to households with propane systems. Like its natural gas counterpart, the D85500PE also has a 50-gallon capacity and delivers a comparable recovery rate. Both models feature a glass-lined tank, providing corrosion resistance and extending the lifespan of the water heater. This protective lining is crucial for maintaining water quality and ensuring durability over time.

In terms of technology, both the D85500NE and D85500PE are equipped with advanced thermostat and burner systems that allow for precise temperature control. The integrated piezo ignition allows for easy start-up, enabling users to ignite the burner with a simple push of a button. Additionally, the water heaters are designed with safety features such as a pressure relief valve, which prevents excessive pressure build-up.

Another notable characteristic of these models is their user-friendly accessibility. Maintenance access is made simple with installation features that enable straightforward servicing and repairs. The compact design of the units also allows for versatile installation options, whether in a basement, garage, or utility closet.

Finally, both the D85500NE and D85500PE are backed by a solid warranty, providing peace of mind for consumers. With their combination of efficiency, reliability, and advanced features, these water heaters from Reliance Water Heaters are an outstanding choice for anyone looking to enhance their home’s hot water system.
Top Page Image Contents