Renesas M30870T-EPB - page 30

M30870T-EPB User’s Manual 2. Setup

REJ10J0482-0300 Rev.3.00 February 16, 2006

2.9.1 Connecting to a 100-pin LCC Socket

When connecting the emulation probe to a 100-pin LCC socket (Yamaichi Electronics Co., Ltd.: IC61-1004-051 etc.) on the

user system, following the procedure below.

(1) Attach the CN2 side of the M30870T-EPB to the CN2 side of the M30800T-PTC.

(2) Attach the M30800T-PTC to the 100-pin LCC socket.

Figure 2.8 Connecting to a 100-pin LCC socket

CAUTION

Notes on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the emulator

and user system.

 The small connectors of the M30870T-EPB and M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

 For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics Co., Ltd.

http://www.yamaichi.co.jp/e/index.shtml

100-pin LCC socket

M3T-FLX160-EPB

M30870T-EPB

CN2 side

(1)

No. 1 pin

(2)

M30800T-PTC

User system

Page 30 of 104

Contents

Main M30870T-EPB User's Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT WARNING Page Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger 2.3 Connecting the Host Machine 2.4 Connecting the PC7501 2.5 Connecting the Power Supply for the Emulator 2.6 Turning ON the Power TARGET SYSTEM 2.7 Downloading Firmware 2.8 Self-check Page 2.9 Connecting the User System Page Page Page Page Page * * * M30870T-EPB Users Manual 2. Setup REJ10J0482-0300 Rev.3.00 February 16, 2006 Page 38 of 104 2.10 Setting Switches RENESAS M30870T-EPBM REV.C RENESAS M30870T-EPBM REV.B Page Page Page Page Page Page Page Page Page C1, C3: Vref-Avss bypass capacitor C2, C4: AVcc-Avss bypass capacitor C1 C2 AVss V REF AV C4 C3 AVss C1, C3: Vref-Avss bypass capacitor C2, C4: AVcc-Avss bypass capacitor C1 C2 AVss V REF AV AVccAVss C4 3. Usage (Emulator Debugger) 3.1 Starting Up the Emulator Debugger (Init Dialog Box) Page Page Page Page Page Page 3.2 Starting Up the Emulator Debugger (EMEM Dialog Box) Page Page Page Page 3.3 Program Window Page M30870T-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J0482-0300 Rev.3.00 February 16, 2006 (3) Setting breakpoints 1. Screen after breakpoint setup Breakpoint setup screen Page 64 of 104 Page 3.4 Hardware Breakpoint Setting Window Page Page Page Page 3.5 Trace Window M30870T-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J0482-0300 Rev.3.00 February 16, 2006 Explanation of the trace window (bus display) 2. Trace window (bus display) Page 72 of 104 Bus display The following explains the displayed contents, from left to Disassemble display Symbol Status Source display Page Page Page 3.6 RAM Monitor Window Page Page 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page Page M30870T-EPB Users Manual 4. Hardware Specifications REJ10J0482-0300 Rev.3.00 February 16, 2006 Page 83 of 104 *: Connected to the inside of the emulator 4.3 Connection Diagrams User system Figure 4.1 Connection diagram (when using M30870T-EPBM REV.B) (1/3) IC1 IC15 Figure 4.2 Connection diagram (when using M30870T-EPBM REV.C) (2/3) IC1 IC15 Unit 2.0 - 160 - RON ON resistor 4.5 - 70 100 RON ON resistor difference 4.5 - 10 - IIN Switch input leak current 12.0 - - 100 nA 4.4 External Dimensions Page Page 4.5 Notes on Using This Product Page Page Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair