Renesas M30870T-EPB - page 59

M30870T-EPB User’s Manual 3. Usage (Emulator Debugger)

REJ10J0482-0300 Rev.3.00 February 16, 2006

(2) Emulation Memory tab

1. Setting the Bank Address of the Debug Monitor

Setting the Bank Address of the Debug

IMPORTANT

Notes on Setting a Debug Monitor Bank Address:

 It is not possible to view or set the content of the specified area. Even on the memory window or in the reverse

assemble area of the program/source windows, the content of this area is not displayed correctly though it can

be displayed.

 The below bank addresses cannot be set for the debug monitor.

(1) MCU internal resources (ROM, RAM and SFR areas)

(2) Multiplex areas

(3) Interrupt vector area

Monitor

The debug monitor uses contiguous 64 KB as a work area o

f

the emulator. Specify the bank address of the debug

monitor.

(e.g.: If D0 is specified, 64 KB area from D00000H address

is used by the debug monitor)

A

utomatically

A

llocating the Emulation

Memory of the Internal ROM

When selecting the single-chip mode or memory expansio

n

mode, an emulation memory is automatically allocated to an

internal ROM area. The automatically allocated addresses o

f

the internal ROM are shown here.

Page 59 of 104

Contents

Main M30870T-EPB User's Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT WARNING Page Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger 2.3 Connecting the Host Machine 2.4 Connecting the PC7501 2.5 Connecting the Power Supply for the Emulator 2.6 Turning ON the Power TARGET SYSTEM 2.7 Downloading Firmware 2.8 Self-check Page 2.9 Connecting the User System Page Page Page Page Page * * * M30870T-EPB Users Manual 2. Setup REJ10J0482-0300 Rev.3.00 February 16, 2006 Page 38 of 104 2.10 Setting Switches RENESAS M30870T-EPBM REV.C RENESAS M30870T-EPBM REV.B Page Page Page Page Page Page Page Page Page C1, C3: Vref-Avss bypass capacitor C2, C4: AVcc-Avss bypass capacitor C1 C2 AVss V REF AV C4 C3 AVss C1, C3: Vref-Avss bypass capacitor C2, C4: AVcc-Avss bypass capacitor C1 C2 AVss V REF AV AVccAVss C4 3. Usage (Emulator Debugger) 3.1 Starting Up the Emulator Debugger (Init Dialog Box) Page Page Page Page Page Page 3.2 Starting Up the Emulator Debugger (EMEM Dialog Box) Page Page Page Page 3.3 Program Window Page M30870T-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J0482-0300 Rev.3.00 February 16, 2006 (3) Setting breakpoints 1. Screen after breakpoint setup Breakpoint setup screen Page 64 of 104 Page 3.4 Hardware Breakpoint Setting Window Page Page Page Page 3.5 Trace Window M30870T-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J0482-0300 Rev.3.00 February 16, 2006 Explanation of the trace window (bus display) 2. Trace window (bus display) Page 72 of 104 Bus display The following explains the displayed contents, from left to Disassemble display Symbol Status Source display Page Page Page 3.6 RAM Monitor Window Page Page 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page Page M30870T-EPB Users Manual 4. Hardware Specifications REJ10J0482-0300 Rev.3.00 February 16, 2006 Page 83 of 104 *: Connected to the inside of the emulator 4.3 Connection Diagrams User system Figure 4.1 Connection diagram (when using M30870T-EPBM REV.B) (1/3) IC1 IC15 Figure 4.2 Connection diagram (when using M30870T-EPBM REV.C) (2/3) IC1 IC15 Unit 2.0 - 160 - RON ON resistor 4.5 - 70 100 RON ON resistor difference 4.5 - 10 - IIN Switch input leak current 12.0 - - 100 nA 4.4 External Dimensions Page Page 4.5 Notes on Using This Product Page Page Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair