Renesas M32100T-EZ-E Chapter 2. Preparation

( 14 / 42 )

Chapter 2. Preparation

2.1 Terminology

Some specific words used in this user's manual are defined as follows:

Emulator system

This means an emulator system built around the M32100T-EZ-E emulator. The M32100T-EZ-E

emulator system is configured with an emulator, host machine, emulator debugger and target board.

Emulator (M32100T-EZ-E)

This means an emulator for the M32R Family MCUs on which the debug interface SDI (Scalable

Debug Interface) is mounted. This emulator is connected to the target board via the SDI interface

cable.

Host machine

This means a personal computer used to control the emulator.

Emulator debugger

This means the software tool PD32RM to control the emulator from the host machine through an

interface. The PD32RM is included with this product.

Firmware

Program that analyzes contents of communication with the emulator debugger and controls the

emulator hardware. This program is downloadable from the emulator debugger PD32RM when

occasion demands.

Target MCU

This means the microcomputer you are going to debug.

Target system

This means a user's application system using the microcomputer to be debugged.

Target board

This means a board using the microcomputer to be debugged.

Target program

This means a program using the microcomputer to be debugged.

JTAG connection

A connection of the emulator via the MCU installed in the target board and the SDI interface

connector. In this case, the MCU on the target board executes the target program.

Contents

Main ( 2 / 42 ) Preface To use the product properly Precautions for Safety Contents Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION WARNING CAUTION Notes on Product Information: Notes on Downloading Firmware: Notes on USB Interface: Notes on Dependencies on the MCU Model: Note on Stack Capacity and Stack Pointer: Page Notes on Target System: Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 System Configuration of the M32100T-EZ-E (1) JTAG Connection 2.4 Name of Each Part Here explains the name and function of each part. (1) Names and Functions of Parts on the Upper Panel Page (2) Names and Functions of Parts on the Side Panel (3) Names and Functions of Parts on the Front Panel (4) Names and Functions of Parts on the Rear Panel Page Chapter 3. Setup 3.1 Connecting the Host Machine 3.2 Connecting the Target System (1) Connecting the SDI Interface Connector Figure 3.3 Connecting the SDI interface cable (2) SDI MCU Control Interface Connector Page (3) Emulator Side Circuit Diagram Page Page Chapter 4. Usage 4.1 Turning on the Power Supply (1) Checking the Connections of the System (2) Turning On/Off the Power Supply Notes on Power Supply to the Target Board: Note on Downloading Firmware: Page Page ( 32 / 42 ) Chapter 5. Specifications 5.1 Specifications Table 5.1 lists specifications of the M32100T-EZ-E. Table 5.1 Specifications of the M32100T-EZ-E Page ( 34 / 42 ) Chapter 6. Troubleshooting 6.1 Flowchart to Remedy Troubles Figure 6.1 Flowchart to remedy troubles See the emulator debugger online help. See, "3.2 Connecting the Target System" (page 23). 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of the M32100T-EZ-E is Abnormal See the M32100T-EZ-E User's Manual. See "4.1 Turning on the Power Supply" (page 28). Table 6.1 LED's abnormal display and its checkpoints (2) Errors Occur When the Emulator Debugger Starts Up Table 6.2 Checkpoints of errors when starting up the emulator debugger Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions CAUTION Note on Transporting the Product: