Manuals / Brands / Computer Equipment / Network Card / Renesas / Computer Equipment / Network Card

Renesas M32100T-EZ-E 2.3 System Configuration of the M32100T-EZ-E

1 42

Download 42 pages, 306.26 Kb

( 16 / 42 )

2.3 System Configuration of the M32100T-EZ-E

Because the M32100T-EZ-E uses a debug interface SDI (Scale Debug Interface) built in the MCU,

JTAG connection is available, which can directly control the MCU installed in the target board.

(1) JTAG Connection

The system configuration when using the M32100T-EZ-E by JTAG connection is shown below.

(1) Host machine (Personal computer)

(2) Emulator (M32100T-EZ-E)

(3) Emulator debugger (PD32RM)

(4) SDI MCU control interface cable

(5) USB interface cable

Figure 2.1 System configuration (JTAG connection)

Use the provided SDI interface cable to connect an SDI connector you prepare on the target board.

Because the emulator is connected to the target board using the SDI MCU control interface connector

(10-pin), the flexibility of designing around the MCU on the target board increases. It can be used

for debugging and evaluation on a test machine.

Directly installed on the target board, the target MCU will not cause problems on electrical equivalent

and poor connection.

Target board

Emulator debugger PD32RM

SDI MCU control interface cable

Emulator M32100T-EZ-E

Host machine (not included)

USB interface

Contents

Main ( 2 / 42 ) Preface To use the product properly Precautions for Safety Contents Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION WARNING CAUTION Notes on Product Information: Notes on Downloading Firmware: Notes on USB Interface: Notes on Dependencies on the MCU Model: Note on Stack Capacity and Stack Pointer: Page Notes on Target System: Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 System Configuration of the M32100T-EZ-E (1) JTAG Connection 2.4 Name of Each Part Here explains the name and function of each part. (1) Names and Functions of Parts on the Upper Panel Page (2) Names and Functions of Parts on the Side Panel (3) Names and Functions of Parts on the Front Panel (4) Names and Functions of Parts on the Rear Panel Page Chapter 3. Setup 3.1 Connecting the Host Machine 3.2 Connecting the Target System (1) Connecting the SDI Interface Connector Figure 3.3 Connecting the SDI interface cable (2) SDI MCU Control Interface Connector Page (3) Emulator Side Circuit Diagram Page Page Chapter 4. Usage 4.1 Turning on the Power Supply (1) Checking the Connections of the System (2) Turning On/Off the Power Supply Notes on Power Supply to the Target Board: Note on Downloading Firmware: Page Page ( 32 / 42 ) Chapter 5. Specifications 5.1 Specifications Table 5.1 lists specifications of the M32100T-EZ-E. Table 5.1 Specifications of the M32100T-EZ-E Page ( 34 / 42 ) Chapter 6. Troubleshooting 6.1 Flowchart to Remedy Troubles Figure 6.1 Flowchart to remedy troubles See the emulator debugger online help. See, "3.2 Connecting the Target System" (page 23). 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of the M32100T-EZ-E is Abnormal See the M32100T-EZ-E User's Manual. See "4.1 Turning on the Power Supply" (page 28). Table 6.1 LED's abnormal display and its checkpoints (2) Errors Occur When the Emulator Debugger Starts Up Table 6.2 Checkpoints of errors when starting up the emulator debugger Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions CAUTION Note on Transporting the Product: