LIGHTING INSTRUCTIONS FOR HEATERS WITH ELECTRONIC IGNITION (IID) For Models with Manual Gas Valves 512, 627, 726

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING:If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

B.BEFORE OPERATING Smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

*Do not try to light any appliance.

*Do not touch any electric switch:

do not use any phone in your building.

*Immediately call your gas supplier from your neighbor’s phone. Follow the gas supplier’s instructions.

*If you cannot reach your gas supplier, call the fire de- partment.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

OPERATING INSTRUCTIONS

1.STOP! Read the safety information above on this label.

2.Set the thermostat on the lowest setting.

3.Turn off all electric power to the appliance.

4.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

5.Remove boiler door panel.

6.For Robertshaw gas valve: Turn gas control knob

clockwise to “OFF”.

For Honeywell Gas Valve: Turn gas control knob clock-

wise to “OFF". Make sure knob rest against stop.

For Honeywell Gas Valve:

Push in gas control knob slightly and turn clockwise

to “OFF”. Knob cannot be turned to “OFF” unless knob is pushed in slightly. Do not force.

7.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information previously stated. If you do not smell gas, go to the next step.

8.For Robertshaw Gas Valve: Turn gas control knob

counter clockwise to “ON”.

For Honeywell Gas Valve: Turn gas control knob

counter clockwise from “OFF” until it stops. Push in gas control knob and continue

rotating counter clockwise to “ON” position. Make sure knob rest against stop.

GAS CONTROL

KNOB SHOWN

IN"ON"POSITION

GAS INLET

Fig. # 8082

9.Replace boiler door panel.

10.Turn on all electric power to the appliance.

11.Set thermostat to desired setting.

12.If the appliance will not operate, follow the instructions “To Turn Off Gas To Appliance” and call your service technician or gas supplier.

GAS CONTROL

KNOB SHOWN

IN"ON"POSITION

GAS INLET

Fig. # 8080

TO TURN OFF GAS TO APPLIANCE

1.Set the thermostat to the lowest setting.

2.Turn off all the electric power to the appliance if service is to be performed.

3.Remove door panel.

4.For Robertshaw Gas Valve: Turn gas control knob

clockwise to “OFF”.

For Honeywell Gas Valve: Turn gas control knob clock-

wise to “OFF”. Make sure knob rest against stop.

For Honeywell Gas Valve:

Push in gas control knob slightly and turn clockwise to “OFF”.

5.Replace heater door panel.

31

Page 30 Page 32
Page 31
Image 31
Rheem 136-1826 installation instructions For Your Safety Read Before Operating
Page 30 Page 32

136-1826 specifications

The Rheem 136-1826 is a highly efficient heating and cooling unit designed to provide reliable performance and comfort in residential settings. This unit is particularly notable for its advanced features, robust technologies, and outstanding characteristics that set it apart in the HVAC market.

One of the defining features of the Rheem 136-1826 is its energy efficiency. Rated with a high Seasonal Energy Efficiency Ratio (SEER), this unit efficiently converts energy into cooling output, leading to significant savings on utility bills. The environmentally friendly refrigerants used in its operation comply with current global regulations and aim to minimize any negative impact on the ozone layer.

Additionally, the Rheem 136-1826 incorporates advanced climate control technologies. Its innovative multi-stage compression offers superior cooling performance and an enhanced ability to maintain comfortable temperatures, even during extreme weather conditions. The variable-speed motor allows for precise airflow management, leading to quieter operation and improved indoor air quality by minimizing dust and allergens in circulation.

Another remarkable attribute of the Rheem 136-1826 is its smart technology integration. Homeowners can connect the unit to Wi-Fi and control it remotely through a mobile app. This feature not only provides convenience but also allows users to monitor system performance, adjust settings, and receive maintenance reminders. The programmable thermostat included in the setup further enhances energy conservation efforts, enabling users to tailor their heating and cooling schedules to their lifestyle.

In terms of installation and maintenance, the Rheem 136-1826 has been designed with user-friendliness in mind. Its compact size allows for easy installation in various locations, making it a versatile choice for different home designs. The durable construction materials used in this unit ensure longevity and reduced maintenance needs over time.

Overall, the Rheem 136-1826 stands out for its combination of energy efficiency, advanced cooling technologies, smart features, and ease of use. It is an ideal choice for homeowners looking for a reliable and efficient heating and cooling solution that not only enhances indoor comfort but also contributes to long-term energy savings. Whether replacing an old system or installing a new one, the Rheem 136-1826 is well-equipped to meet the demands of modern living.
Top Page Image Contents