Electrical Electronic Ignition IID Models 512

ELECTRICAL (ELECTRONIC IGNITION IID) MODELS 512 - 1826

C.Trouble shooting for S8600 control. Refer to the following chart for future servicing or the ignition control.

WARNING HIGH VOLTAGE

For qualified Technicians ONLY

NOTE: Some heaters may be equipped with an ignition module that shuts off pilot gas if pilot fails to light. To reset, interrupt power to heater.

START

TURN GAS SUPPLY OFF.

TURN THERMOSTAT

(CONTROLLER) TO CALL

FOR HEAT

POWER TO MODULE

(24 V NOMINAL)

YES

Intermittent Pilot System

TROUBLESHOOTING HONEYWELL S8600

NOTE: Before troubleshooting, familiarize yourself with the start-up and checkout procedure.

NO	Check line voltage power, low voltage transformer, limit controller,
	thermostat (controller) and wiring.

SPARK ACROSS

IGNITER/SENSOR GAP

YES

Pull ignition lead and check spark at module.

Spark Okay?

YES

•Check ignition cable, ground wiring, ceramic insulator and gap, and correct.

•Check boot of the ignition cable for signs of melting or buckling. Take protective action to shield cable and boot from excessive temperatures.

TURN GAS SUPPLY ON

PILOT BURNER LIGHTS?

YES

SPARK STOPS WHEN

PILOT IS LIT?

YES

MAIN BURNER LIGHTS?

YES

SYSTEM RUNS UNTIL CALL FOR HEAT ENDS?

YES

		• Check that all manual gas valves are open, supply tubing and pressures are
NO
NO
		good, and pilot burner orifice is not blocked.
		good, and pilot burner orifice is not blocked.

•Check electrical connections between module and pilot operator on gas control.

•Check for 24 Vac across PV-MV/PV terminals on module. If voltage is okay, replace gas control; if not, replace module.

	NOTE: If S8600H goes into lockout, reset system. Lockout is used on L.P.G. models.


NO	•	Check continuity of ignition cable and ground wire.
NO	•	Check continuity of ignition cable and ground wire.
	•	Clean flame rod.
	•	Check electrical connections between flame rod and module.
	•	Check for cracked ceramic flame rod insulator.
	•	Check that pilot flame covers flame rod and is steady and blue.
	•	Adjust pilot flame.
	•	If problem persists, replace module.

	•	Check for 24 Vac across MV-MV/PV terminals. If no voltage, replace module.
NO	•
	•	Check electrical connections between module and gas control. If okay, replace
	•
		gas valve or gas control operator, i.e. pilot gas valve, flow switch etc.

NOTE: IF S8600H goes into lockout, reset system.

NO	• Check continuity of ignition cable and ground wire.

NOTE: If ground is poor or erratic, shutdowns may occur occasionally even though operation is normal at the time of checkout.

•Check that pilot flame covers flame rod and is steady and blue.

•If checks are okay, replace module.

CALL FOR HEAT ENDS

SYSTEM SHUTS OFF?

YES

TROUBLESHOOTING

ENDS

NO	•	Check for proper thermostat (controller) operation.

	•	Remove MV lead at module; if valve closes, recheck temperature controller and

		wiring; if not, replace gas valve.

Repeat procedure until troublefree operation is obtained.

136-1826 specifications

The Rheem 136-1826 is a highly efficient heating and cooling unit designed to provide reliable performance and comfort in residential settings. This unit is particularly notable for its advanced features, robust technologies, and outstanding characteristics that set it apart in the HVAC market.

One of the defining features of the Rheem 136-1826 is its energy efficiency. Rated with a high Seasonal Energy Efficiency Ratio (SEER), this unit efficiently converts energy into cooling output, leading to significant savings on utility bills. The environmentally friendly refrigerants used in its operation comply with current global regulations and aim to minimize any negative impact on the ozone layer.

Additionally, the Rheem 136-1826 incorporates advanced climate control technologies. Its innovative multi-stage compression offers superior cooling performance and an enhanced ability to maintain comfortable temperatures, even during extreme weather conditions. The variable-speed motor allows for precise airflow management, leading to quieter operation and improved indoor air quality by minimizing dust and allergens in circulation.

Another remarkable attribute of the Rheem 136-1826 is its smart technology integration. Homeowners can connect the unit to Wi-Fi and control it remotely through a mobile app. This feature not only provides convenience but also allows users to monitor system performance, adjust settings, and receive maintenance reminders. The programmable thermostat included in the setup further enhances energy conservation efforts, enabling users to tailor their heating and cooling schedules to their lifestyle.

In terms of installation and maintenance, the Rheem 136-1826 has been designed with user-friendliness in mind. Its compact size allows for easy installation in various locations, making it a versatile choice for different home designs. The durable construction materials used in this unit ensure longevity and reduced maintenance needs over time.

Overall, the Rheem 136-1826 stands out for its combination of energy efficiency, advanced cooling technologies, smart features, and ease of use. It is an ideal choice for homeowners looking for a reliable and efficient heating and cooling solution that not only enhances indoor comfort but also contributes to long-term energy savings. Whether replacing an old system or installing a new one, the Rheem 136-1826 is well-equipped to meet the demands of modern living.

Rheem 136-1826 installation instructions Electrical Electronic Ignition IID Models 512, Start

Models: 136-1826