Manuals
/
Rheem
/
Household Appliance
/
Water Heater
Rheem
300 series installation instructions This page is intentionally blank
Models:
300 series
1
29
32
32
Download
32 pages
18.97 Kb
25
26
27
28
29
30
31
32
<
>
Install
Warranty
Dimension
Close Down Procedure
Temperature Adjustment
Thermostat setting
TEMPERATURE PRESSURE RELIEF VALVE RUNNING Normal Operation
Safety
Save A Service Call
A copper drain line must be fitted to the relief valve to carry the discharge clear of the water heater. Connect the drain line to the relief valve using a disconnection union. The pipe work from the relief valve to the drain should be as short as possible and fall all the way from the water heater with no restrictions. It should have no more than three right angle bends in it. Use DN15 pipe
Page 29
Image 29
This page is intentionally blank
29
Page 28
Page 30
Page 29
Image 29
Page 28
Page 30
Contents
Please leave this guide with the householder
Owners Guide and Installation Instructions
Gas Domestic Indoor Water Heater
Victorian Plumbing Industry Commission
Notice to Victorian Customers from the
the Victorian Building Act
PATENTS
HOUSEHOLDER - We recommend you read pages 4 to
CONTENTS
ABOUT YOUR WATER HEATER
TEMPERATURE ADJUSTMENT
MODEL TYPE
HOW HOT SHOULD THE WATER BE?
ABOUT YOUR WATER HEATER
SAFETY
TO TURN OFF THE WATER HEATER
DOES THE WATER QUALITY AFFECT THE WATER HEATER?
TO TURN ON THE WATER HEATER
HOW LONG WILL THE WATER HEATER LAST?
ANODE PROTECTION
MAINS PRESSURE
HOW YOUR WATER HEATER WORKS
PIEZO IGNITION
PILOT IGNITER
lift until water flows from the drain line - lower gently
REGULAR CARE
drain line
water heater
REGULAR CARE
EXPANSION CONTROL VALVE
SERVICING
Temperature pressure relief valve running
SAVE A SERVICE CALL
Thermostat setting
NOT ENOUGH HOT WATER OR NO HOT WATER
Continuous dribble
TEMPERATURE PRESSURE RELIEF VALVE RUNNING Normal Operation
Steady flows for long period often at night
NEVER replace the relief valve with one of a higher pressure rating
Is there a normal gas supply to the rest of the premises?
CAN’T LIGHT THE PILOT FLAME
WATER HEATER APPEARS TO BE LEAKING
HIGH GAS BILLS
WATER HEATER LOCATION
INSTALLATION
INSTALLATION
SAFE TRAY
MAINS WATER SUPPLY
HOT WATER DELIVERY
TANK WATER SUPPLY
INSTALLATION
Two Temperature Zones Using a Temperature Limiting Device
CIRCULATED HOT WATER FLOW AND RETURN SYSTEM
Temperature Limiting Device
INSTALLATION
Circulated Hot Water Flow and Return System - Gas Water Heater
ANODE TYPES
REDUCING HEAT LOSSES
SADDLING - PIPE WORK
INSTALLATION
INSTALLATION
DIMENSIONS AND TECHNICAL DATA
Dimensions
Model
INSTALLATION
TYPICAL INSTALLATION - INDOOR LOCATION
WATER INLET AND OUTLET
CONNECTIONS - PLUMBING
CONNECTION SIZES
PIPE SIZES
GAS INLET
RELIEF VALVE
CONNECTIONS - PLUMBING
A copper drain line must be fitted to the relief valve to carry the discharge clear of the water heater. Connect the drain line to the relief valve using a disconnection union. The pipe work from the relief valve to the drain should be as short as possible and fall all the way from the water heater with no restrictions. It should have no more than three right angle bends in it. Use DN15 pipe
RELIEF VALVE DRAIN
CONNECTIONS - PLUMBING
EXPANSION CONTROL VALVE
TO FILL AND TURN ON THE WATER HEATER
COMMISSIONING
GAS INLET PRESSURE
TO TURN OFF THE WATER HEATER
LIGHTING THE WATER HEATER
FOR YOUR SAFETY READ BEFORE LIGHTING
SAFETY INFORMATION
1. Stop, read the safety information on page
Using the gas control light the water heater as follows
LIGHTING INSTRUCTIONS
Note Failure to wait five 5 minutes may result in a fire or explosion
LIGHTING THE WATER HEATER
TEST THE WATER HEATER AFTER INSTALLATION
AIR SHUTTER
1. Turn the gas control knob to the
CLOSE DOWN PROCEDURE
LIGHTING THE WATER HEATER
DRAINING THE WATER HEATER
This page is intentionally blank
ANODE
WATER SUPPLIES
SATURATION INDEX
Refer to the cold water connection detail on page
WARRANTY EXCLUSIONS
RHEEM MAINS PRESSURE WATER HEATER WARRANTY AUSTRALIA ONLY
WARRANTY CONDITIONS
RHEEM MAINS PRESSURE WATER HEATER WARRANTY AUSTRALIA ONLY
WARRANTY