Installing the water heater.

The location chosen for the water heater must take into consideration the following:

Local Installation Regulations

This water heater must be installed in accordance with these instructions, local codes, utility codes, utility company requirements or, in the absence of local codes, the latest edition of the National Electrical Code. It is available from some local libraries or can be purchased from the

National Fire Protection Association, Batterymarch Park, Quincy, MA 02269 as booklet ANSI/NFPA 70.

Canadian installations should refer to CSA22.1, a copy can be purchased from the Canadian Standards Association, 5050 Spectrum Way, mississauga,ONT L4W 5N6

NOTICE: Auxiliary catch pan MUST conform to local codes.

Catch Pan Kits are available from the store where the water heater was purchased, or any water heater distributor.

Catch Pan should not obstruct cold inlet or drain valve.

Location

Locate the water heater in a clean dry area as near as practical to the area of greatest heated water demand. Long un-insulated hot water lines can waste energy and water.

Place the water heater in such a manner that the thermistor and element access panels can be removed to permit inspection and servicing such as removal of elements or checking controls.

The water heater and water lines should be protected from freezing temperatures. Do not install the water heater in outdoor, unprotected areas.

Make certain the floor underneath the water heater is strong enough to sufficiently support the weight of the water heater once it is filled with water.

B

A—Diameter of water heater plus 2" min..

B—Maximum 2″

A

 

!CAUTION: The water heater should not be located in an area where leakage of the tank or connections will result in damage to the area adjacent to it or to lower floors of the structure. Where such areas cannot be avoided, it

is recommended that a suitable catch pan, adequately drained, be installed under the water heater.

NOTICE: Installation in a closet or confined space is not allowed.

Heat Pump Water Heater requires approximately 1,000 cu. ft of unconditioned indoor ambient air to operate properly.

 

Clearances

Rear

 

Top

2"

 

8" Min.

To open drain, line should be at least 3/4″ ID and pitched for proper drainage.

Inspect Shipment

Inspect the water heater for possible damage. Check the markings on the rating plate of the water heater to be certain the power supply corresponds to the water heater requirements. Rating plate is located on front of water heater.

Refrigerant

This heat pump water heater is factory charged with an environmentally friendly, non-chlorinated refrigerant, R410A. This refrigerant has zero ozone depletion potential.

5

Page 5
Image 5
Rheem HP50RU, HP50RH Installing the water heater, Local Installation Regulations, Location, Inspect Shipment, Refrigerant

HP50RH, HP50RU, 92-103234-02, HP40RU, AP15121-1 specifications

The Rheem AP15121-1, HP40RU, 92-103234-02, HP50RU, and HP50RH are central components in Rheem's commitment to providing high-quality water heating solutions. These models represent some of the company’s efficient and technologically advanced offerings designed to meet diverse residential and commercial water heating needs.

One of the standout features of these models is their high energy efficiency, which is critical for reducing operational costs and environmental impact. Many of these units are equipped with advanced energy-saving technologies that comply with stringent energy regulations, ensuring they operate effectively while minimizing energy consumption. For instance, some models have been certified with Energy Star ratings, which guarantees they meet high-energy efficiency standards.

The Rheem HP40RU and HP50RU units are particularly noted for their robust performance, offering capacities of 40 and 50 gallons, respectively. This makes them suitable for households with varying hot water demands, from small families to larger households. The design of these tanks allows for efficient heat retention, which means less energy is required to maintain the desired water temperature.

Additionally, the Rheem AP15121-1 offers technology that integrates smart features, such as Wi-Fi connectivity, enabling users to monitor and manage water heating systems through mobile applications. This feature enhances convenience and provides insights into usage patterns, allowing for better energy management.

In terms of safety and durability, these Rheem models are designed with advanced safety mechanisms, including automatic shut-off features and high-quality materials to prevent leaks and corrosion, prolonging the unit's lifespan. The 92-103234-02 model incorporates a professional-grade design focused on long-term reliability, which is essential for commercial environments.

Another significant characteristic of these models is their user-friendly interfaces and straightforward installation processes, which can minimize installation times and simplify maintenance. Many units come with comprehensive warranties, reflecting Rheem's confidence in their products and providing peace of mind for consumers.

Overall, the Rheem AP15121-1, HP40RU, 92-103234-02, HP50RU, and HP50RH bring a blend of efficiency, reliability, and innovative technology, making them ideal choices for anyone in the market for a durable and effective water heating solution. Whether for residential or commercial needs, these models uphold Rheem's esteemed reputation in the water heating industry.