MAINTENANCE

SEASONAL CLUTCH MAINTENANCE

It is important that the clutches slip when an obstacle or load heavier than the clutch setting is encountered. Therefore, if the machine sits outside longer than 30 days and is exposed to rain and/or humid air it is important to make sure that the clutch lining plates are not rusted/corroded together. Before using the cutter use the following procedure to make sure the clutch will slip and give the overload protection required. The clutch has a single disc spring with 6 adjusting nuts.

1.Loosen nuts (Figure Mnt-R-0090)on springs until the spring is free, yet remains secure on bolts.

2.Attach cutter to tractor and start the tractor. Set the engine speed at 1200 RPM.

3.Mark outer plates as shown in Figure Mnt-R-0090.

4.Engage the PTO (approximately one second) and then quickly disengage it. The friction lining plates should break loose (check the mark).

5.Turn tractor off. Tighten the nuts on the disc spring clutch until they bottom out, then loosen each nut 2 turns.

MOWER STORAGE

Your rotary cutter represents an investment from which you should get the greatest possible benefit. Therefore, when the season is over, the cutter should be thoroughly checked and prepared for storage so that a minimum amount of work will be required to put it back into operation for the next season. The following are suggested storage procedures:

1.Thoroughly clean the cutter.

2.Lubricate the cutter as covered in Maintenance Section.

3.Tighten all bolts and pins to the recommended torque.

4.Check the cutter for worn or damaged parts. Make replacements immediately.

5.Store the cutter in a clean, dry place with the cutter housing resting on blocks.

6.Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the cutter.

PROPER TORQUE FOR FASTENERS

The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to this chart to determine the grade of bolts and the proper torque except when specific torque values are assigned in manual text.

RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL*

NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine oil. They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are used. This applies to both UNF fine and UNC coarse threads.

SE8A 01/11

Maintenance Section 5-17

© 2011 Alamo Group Inc.

MAINTENANCE

Page 172 Page 174
Page 173
Image 173
Rhino Mounts SE8A manual Seasonal Clutch Maintenance, Proper Torque for Fasteners
Page 172 Page 174

SE8A specifications

The Rhino Mounts SE8A is a robust and versatile mounting solution designed for a variety of applications in both professional and casual settings. Known for its innovative design and durability, the SE8A caters to a wide range of users, including filmmakers, content creators, and industrial professionals.

One of the standout features of the SE8A is its compatibility with a variety of equipment, such as cameras, monitors, and other accessories. It supports standard 1/4-20 and 3/8-16 threads, making it easy to mount multiple devices simultaneously or switch between them without hassle. This versatility is crucial for users looking to efficiently leverage their gear in various settings, whether shooting on location or stabilizing devices in a controlled environment.

The design of the SE8A incorporates lightweight yet sturdy materials, allowing for easy transport while ensuring reliability and stability during use. The mount itself has been engineered to handle significant weight without compromising structural integrity, ensuring that equipment remains secure, even under demanding conditions. This robustness is particularly beneficial for outdoor shoots where environmental factors can influence equipment performance.

Another notable technological feature of the SE8A is its adjustable arm mechanism. Users can easily customize the positioning of their devices to achieve the perfect angle for shooting or monitoring. This adaptability allows for creativity during filming and ensures optimal visibility for monitoring purposes. The smooth adjustability reduces the time spent on setups and enables users to focus more on their creative processes.

Additionally, the Rhino Mounts SE8A includes anti-slip rubber grips to prevent any unwanted movement when mounted. This feature is essential for maintaining the desired configuration, ensuring stable shots without the risk of drifting. Users can have confidence in the mounting stability even during dynamic shooting scenarios.

Moreover, the SE8A is designed for quick installation and disassembly. The intuitive locking mechanism allows users to swiftly secure their devices in place or detach them when necessary, making transitions seamless and user-friendly. This ease of use is especially beneficial for professionals who are often on the move and need a reliable solution that won’t consume valuable time.

In conclusion, the Rhino Mounts SE8A is an exceptional mounting solution that combines durability, versatility, and practicality. With features like compatibility, lightweight design, adjustable arms, and anti-slip technology, it is sure to enhance the efficiency and creativity of any user’s workflow, making it a valuable tool for anyone in need of reliable equipment mounting.
Top Page Image Contents