Command No.

 

 

 

 

 

 

 

 

 

 

 

 

Command Descriptions

 

12H:

[Camera function mode setting 3] Initial data: 0

 

MOD3[70]

Sets the following camera function modes.

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

D7~D6:

Video Out

 

 

 

 

 

 

00: 10bit

 

01: 8bit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10: 12bit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11: No function (Prohibited setting. Do not set these values)

 

 

D5:

 

Triggerin connector selection

0: Camera Link ( CC1)

1: /IO connector (No.2 Pin)

 

 

D4~D3:

Exposure Start Mode

 

 

00: Normal

01: Reserved trigger

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10 ~11: H reset

 

 

 

D2~D1:

No Function

 

 

 

 

Set always “000”

 

 

 

D0

 

Lookup table (Gamma)

 

00: OFF

01: ON

 

 

 

 

 

 

 

14H:

[Communication mode] Initial Data: 01H

 

 

 

 

 

UART[70]

Sets the communication modes.

 

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7~D2:

 

No Function

 

 

 

Set always “000000”

 

 

 

D1~D0:

 

Communication Mode

 

00: 38,400 bps

01: 9,600 bps

 

 

 

 

 

 

 

 

 

 

 

 

 

10: 57,600 bps

11: 115,200 bps

 

 

 

1CH:

[AGC maximum limit] Initial data: 255, data range: 0 to 255

 

AGCMAX[7..0]

Sets the maximum limit for the AGC.

 

 

 

 

 

 

 

 

 

1DH:

[Target Brightness for ALC] Initial data: 128, data range: 0 to 255

 

ALCTRGT [7..0]

Sets the target brightness for the ALC function (Auto Luminance Control).

 

 

 

 

 

 

 

 

 

 

1EH:

[ALC mode] Initial data: 0

 

 

 

 

 

 

 

 

ALCMODE[7..0]

Sets the ALC modes.

 

 

 

 

 

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

D7:

 

 

Long exposure

 

 

 

0: OFF

 

1: ON

 

 

D6 to D2 No Function

 

 

 

Set always “00000”

 

 

 

D1

 

 

AGC (Auto Gain Control)

0: OFF

1: ON

 

 

D0

 

 

AE (Auto Exposure)

 

0: OFF

1: ON

 

When using AE combined with the long exposure, exposure time is controlled regardless of the frame rate.

 

Therefore, the frame rate varies depending on the exposure time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FVL030B1

26/32

User’s Guide Rev. 1.01

 

Page 26
Image 26
Ricoh FV-L030B1 manual 26/32