Rinnai RHFE-1510F manual This is done by pulling the outside terminal

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Separate the Terminal into 3 parts; sleeve plate, connection manifold, and the terminal body.

This is done by pulling the outside terminal
from the connection manifold, then pull sleeve
	￿￿￿￿￿￿￿￿￿￿￿	￿￿￿￿￿￿	￿￿￿￿￿￿￿￿
off outer terminal. Spread springs out so they
are slightly bigger than the hole.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿

Extension tube (optional extra) is needed for any extension.

Maximum￿extension is 5m in length This allows for a maximum of￿￿￿bends￿

Maximum 3 bends

Maximum￿5m length

￿￿￿￿￿￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿￿	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
ing		￿￿￿￿
Push the terminal body through from outside.
-Install the terminal body tilting at a slight angle to
the surface and stick it firmly to the wall.		￿￿￿￿

-Put silicon between the wall and the flue terminal so there is no gap after fixing the flue terminal.

￿￿￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
ing
Insert the sleeve plate over the spring loaded	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
ties of the terminal body. Be careful not
to damage the O-ring on the body.
Pull the ties tight so the sleeve plate		￿
sticks to the wall then fix the ties on sleeve plate

Condensed water can form in the tube

when￿extended. Make sure there are no low spots. Do not run ￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

If condensed water comes in to the heater, the water tray can overflow. Do

not run flue more than 2m vertically.

￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿ Low Spot

￿￿￿￿￿￿￿￿￿

￿￿

lugs. They will extend 2-3 slots past start point.
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿ties￿￿￿￿￿￿￿￿￿￿the ￿￿￿￿￿￿￿￿￿￿￿￿tie.		￿￿￿￿￿￿￿￿￿
- Flange is marked This way up with an arrow
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿stick through￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
or the word Top, and must be installed this
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
way.
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
-￿￿￿￿￿￿￿￿￿Secure the sleeve to the wall using the 4
holes￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿of the flange.
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
- After sleeve is secure, cut off the rest of the
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
tie. (The parts that stick through to the inside.)
- Insert connection manifold into Sleeve.			￿
Secure with the 3 screws provided. The
manifold can be turned to any angle.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿s￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

of flue tube must be same.

23 24