High Level Inputs | Rockford Fosgate 5.3x specification

◆High Level Inputs

The high level inputs on the Rockford Fosgate amplifiers convert the speaker line outputs (high level) to preamp line inputs (low level). This allows amplifier compatibility with a variety of source units as well as the ability to integrate into factory systems without the need for external adapters.

THE RESULT: Allows compatibility with factory and aftermarket source units.

◆XCard Crossover

The 5.3x amplifiers utilize internal active crossovers. These cross- overs have many performance advantages such as using discrete components for exact frequency adjustments which are far superior to potentiometers. Additionally, the XCard can be configured for high-pass, low-pass and full range operation. With slight modifica- tion, many crossover frequencies and slope configurations can be achieved.

THE RESULT: Increased system design flexibility with a precise electronic crossover without the limitations of conventional poten- tiometer designs.

◆Signal Switching Network

The Signal Switching Network allows the RCA input signals to be distributed to the amplifier channels in many different configura- tions. Among the many possible configurations, one setting uses a single RCA (L mono) to feed the subwoofer channel, thus simplifying connections needed.

THE RESULT: Allows input signals to be distributed to amplifier channels in many different configurations.

– 4 –

Image 7

Rockford Fosgate 5.3x manual High Level Inputs

Contents

Channel w/crossovers Installation a n d O p e r a t i o n Practice Safe Sound T T I N G S T a R T E D TA B L E O F CO N T E N T S Technical Design Features Accessory PackT R O D U C T I O N Mosfet Devices DSM Discrete Surface Mount Technology High Level Inputs 3X DE S I G N FE AT U R E S Dual Extruded Heatsinks Power/Speaker Barrier StripLED Power Indicator Signal Input Switches S TA L L AT I O N CO N S I D E R AT I O N S Trunk Mounting Mounting Location WI R I N G T H E SY S T E M Battery and Charging Cut Using Passive Crossovers Ohms Table of Crossover Component Values Customizing the Xcard US I N G T H E Xcard Butterworth Alignment Q = Resistor Chart Xcard Access Front inputs Using the Signal Switching NetworkConfiguration #2 Configuration #3 Configuration #6 Configuration #5Front inputs = Front, Rear Subwoofer outputs Subwoofer L Mono inputs Configuration #1 Front inputs Configuration #2 Front inputs Factory Subwoofer L Mono inputs Configuration #4 Mono Sub Input Front inputs Configuration #5 Front inputs Watts Total Power High Level Input Single Ended Type 3X Installation Factory Radio 100.7 High Level Input B.T.L. Type Channel Operation Power Connections Sub Gain Control operates independently Channel Mono Operation Step #1 System Diagrams Step #2 Step #3 Front XCard Step #4 TR O U B L E S H O O T I N G Symptom Diagnosis Remedy Speaker Output Engine noise with Listening to Loudspeakers Not Resistors About the Dynamic Power MeasurementsDY N a M I C PO W E R ME a S U R E M E N T S Music Information Cubed What is an Amplifier? Front/Rear Sub Channels 3X Specifications ATC Limited WA R R a N T Y in F O R M AT I O N Length of WarrantyPage Utilizacion DEL Circuito DE Conmutacion DE Señal Introducción Posteriores Configuración n3Configuración n5 Configuración n6 Utilisation DU Réseau DE Commutation DU Signal Arrière Somme avant & arrière Einleitung Benutzen DES Signal Netzwerkes Vordere Eingänge = Vordere & Hintere Beispiel #3Beispiel #5 Beispiel #6 Introduzione Configurazione #2Impiegare LA Rete DI Selezione Degli Ingressi Posteriore sommati ConfigurazioneConfigurazione #4 Ingresso sub mono Ingressi anteriore Made in the USA