Dual Extruded Heatsinks, RCA Input Jacks | Rockford Fosgate 5.3x

1.Dual Extruded Heatsinks

The dual extruded aluminum heatsinks of this RF amplifier dissipate heat generated by the amplifier's circuitry.

2.Power/Speaker Barrier Strip

The barrier strip uses screw terminals that will accept #10 spade lugs or bare speaker and power wire sizes from 10-18 AWG. These gold-plated connectors are immune to corrosion that will cause signal degradation.

3.RCA Input Jacks

The industry standard RCA jack provides an easy connection for signal level input. They are gold-plated to resist the signal degradation caused by corrosion.

4.High Level Inputs

The high level input connectors accept 1/8" spade lugs for the connection of a source unit that has only speaker line (high level) outputs.

5.Input Sensitivity Controls

The input level controls are preset for 500mV which will match the output of most source units. They can be adjusted to match output levels from a variety of source units.

6.Internal Crossovers

The built-in crossover cards are configurable for a multitude of operating frequencies. The orientation of the card in its socket determines its function of high-pass, low-pass or full range operation.

7.LED Power Indicator

The LED gives a visual indication of the status of the amplifier, lighting when the unit is turned on.

8.Signal Input Switches

These switches allow the input signals to be distributed to the outputs in many different configurations.

9.Bias Controls

The Bias controls are preset at the factory and are not user adjustable. CAUTION! ANY ADJUSTMENT TO THE BIAS

CONTROLS WILL VOID YOUR WARRANTY!

– 6 –

Image 9

Rockford Fosgate 5.3x manual Dual Extruded Heatsinks, Power/Speaker Barrier Strip, RCA Input Jacks, High Level Inputs

Contents

Channel w/crossovers Installation a n d O p e r a t i o n Practice Safe Sound T T I N G S T a R T E D TA B L E O F CO N T E N T S Accessory Pack Technical Design FeaturesT R O D U C T I O N Mosfet Devices DSM Discrete Surface Mount Technology High Level Inputs 3X DE S I G N FE AT U R E S LED Power Indicator Power/Speaker Barrier StripSignal Input Switches Dual Extruded Heatsinks S TA L L AT I O N CO N S I D E R AT I O N S Trunk Mounting Mounting Location WI R I N G T H E SY S T E M Battery and Charging Cut Using Passive Crossovers Ohms Table of Crossover Component Values Customizing the Xcard US I N G T H E Xcard Butterworth Alignment Q = Resistor Chart Xcard Access Configuration #2 Using the Signal Switching NetworkConfiguration #3 Front inputs Configuration #5 Configuration #6Front inputs = Front, Rear Subwoofer outputs Subwoofer L Mono inputs Configuration #1 Front inputs Configuration #2 Front inputs Factory Subwoofer L Mono inputs Configuration #4 Mono Sub Input Front inputs Configuration #5 Front inputs Watts Total Power High Level Input Single Ended Type 3X Installation Factory Radio 100.7 High Level Input B.T.L. Type Channel Operation Power Connections Sub Gain Control operates independently Channel Mono Operation Step #1 System Diagrams Step #2 Step #3 Front XCard Step #4 TR O U B L E S H O O T I N G Symptom Diagnosis Remedy Speaker Output Engine noise with DY N a M I C PO W E R ME a S U R E M E N T S About the Dynamic Power MeasurementsMusic Listening to Loudspeakers Not Resistors Information Cubed What is an Amplifier? Front/Rear Sub Channels 3X Specifications ATC Limited WA R R a N T Y in F O R M AT I O N Length of WarrantyPage Utilizacion DEL Circuito DE Conmutacion DE Señal Introducción Configuración n5 Configuración n3Configuración n6 Posteriores Utilisation DU Réseau DE Commutation DU Signal Arrière Somme avant & arrière Einleitung Benutzen DES Signal Netzwerkes Beispiel #5 Beispiel #3Beispiel #6 Vordere Eingänge = Vordere & Hintere Configurazione #2 IntroduzioneImpiegare LA Rete DI Selezione Degli Ingressi Configurazione #4 Ingresso sub mono ConfigurazioneIngressi anteriore Posteriore sommati Made in the USA