INSTALLATION

This section focuses on some of the vehicle considerations for installing your new Amplifier. Pre- planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

!CAUTION: If you feel unsure about installing this system yourself, have it installed by a qualified technician.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the Unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

The mounting position of your amplified subwoofer will have a great effect on the sound performance produced.

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide the best cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will work but provides less cooling capability than vertical mounting.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

5

Page 4 Page 6
Page 5
Image 5
Rockford Fosgate Mono Amplifier manual Installation, Mounting Locations
Page 4 Page 6

Mono Amplifier specifications

Rockford Fosgate is a name synonymous with high-quality automotive audio systems, and their mono amplifiers are among the best in the market for bass lovers. Designed to deliver powerful performance, these amplifiers provide an exceptional audio experience that elevates your music to a whole new level.

One of the standout features of Rockford Fosgate mono amplifiers is their impressive power output. These amplifiers are engineered to handle substantial power levels, making them perfect for driving subwoofers. The robust MOSFET power supply ensures efficient operation, allowing for maximum output without compromising on sound quality. This results in deep, rich bass that is sure to impress even the most discerning audiophiles.

Rockford Fosgate employs advanced technologies in their mono amplifiers to enhance performance further. The use of Class D topology is a prime example; this design is highly efficient and minimizes heat production. As a result, users can enjoy extended listening sessions without worrying about overheating or excessive power drain. This efficiency also translates to a lighter weight, making installation more straightforward and flexible.

Another notable characteristic is the inclusion of variable low-pass filters (LPF), allowing users to tailor the audio output according to their preferences. With adjustable settings, you can fine-tune the crossover frequency, ensuring that your subwoofers receive the right frequencies for optimal performance. Additionally, many models come with a built-in bass boost feature, allowing users to amplify specific bass frequencies for extra impact.

Durability is also a key aspect of Rockford Fosgate’s mono amplifiers. Constructed with high-quality materials, these amplifiers are designed to withstand the rigors of automotive environments. Features like a full-onboard protection circuit safeguard against overheating, short circuits, and overloading, ensuring longevity and reliability.

Incorporating the latest technologies, Rockford Fosgate mono amplifiers often feature remote bass level control. This handy feature allows users to adjust bass levels on the fly without needing to access the amplifier directly. This flexibility is ideal for those who wish to fine-tune their audio input based on listener preferences or track variations.

In summary, Rockford Fosgate mono amplifiers stand out due to their exceptional power output, efficient Class D topology, customizable audio settings, and durable build quality. These characteristics make them a popular choice for audio enthusiasts looking to enhance their in-car listening experience. Whether you are a casual listener or a dedicated audiophile, these amplifiers offer the power and versatility needed to bring your music to life.
Top Page Image Contents