OPERATION

ADJUSTING CROSSOVER FREQUENCY

Placing the switch in the HP position sets the amplifier to the High Pass mode, enabling frequencies above the cut-off point to pass, adjustable between 40-400Hz.

Placing the switch in the AP position sets the amplifier to the All Pass mode, preventing any crossover adjustment, allowing all frequencies to pass.

Placing the switch in the LP position sets the amplifier to the Low Pass mode, enabling frequencies below the cut-off point to pass, adjustable between 40-400Hz.

Turn the crossover adjustment knob all the way down.With the system playing, turn the crossover adjustment knob up slowly until the desired crossover point is achieved.

TROUBLESHOOTING

NOTE:If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1: Check Amplifier for proper connections.

Verify that POWER light (light on Remote Punch Bass) is on. If POWER light is on skip to Step 2, if not continue.

1.Check in-line fuse on battery positive cable. Replace if necessary.

2.Check fuse(s) on amplifier. Replace if necessary.

3.Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.

4.Verify there is 10.5 - 15.5 Volts present at the positive battery and remote turn-on cable.Verify quality connections for both cables at amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Check Amplifier for audio output.

1.Verify good RCA input connections at stereo and amplifier. Check entire length of cables for kinks, splices, etc.Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

2.Disconnect RCA input from amplifier. Connect RCA input from test stereo directly to amplifier input.

Procedure 3: Check Amplifier if you experience Turn-on Pop.

1.Disconnect input signal to amplifier and turn amplifier on and off.

2.If the noise is eliminated, connect the REM lead of amplifier to source unit with a delay turn-on module.

OR

1.Use a different 12 Volt source for REM lead of amplifier (i.e. battery direct).

2.If the noise is eliminated, use a relay to isolate the amplifier from noisy turn-on output.

Procedure 4: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2.Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

Continued.....

9

Page 8 Page 10
Page 9
Image 9
Rockford Fosgate Punch 45 manual Operation Adjusting Crossover Frequency, Troubleshooting
Page 8 Page 10

Punch 45 specifications

The Rockford Fosgate Punch 45 is a classic amplifier renowned for its high performance in the world of car audio. With a legacy that dates back decades, this model continues to be a favorite among audiophiles and casual listeners alike. Characterized by its compact size and impressive power output, the Punch 45 delivers a remarkable audio experience without overwhelming your vehicle's space.

One of the main features of the Punch 45 is its RMS power rating, which typically offers around 45 watts per channel. This output ensures that the amplifier can drive most speakers effectively, producing rich, clear sound even at high volumes. The amplifier supports a variety of speaker configurations, making it a versatile choice for many audio setups. Its two-channel design allows for easy integration into existing systems, including powering front and rear speakers or bi-amping coaxial speakers for enhanced performance.

In terms of technology, the Punch 45 incorporates several advanced features. The amplifier uses a high-efficiency Class AB design, which contributes to its lower heat output and improved overall performance. This allows the unit to run cooler compared to other amplifier types, reducing the risk of thermal shutdown during extended use. The Punch 45 also comes equipped with variable high-pass and low-pass filters, enabling users to tailor their sound experience according to personal preferences and speaker capabilities.

The build quality of the Punch 45 is notably robust, with a durable chassis designed to withstand the rigors of automotive environments. Its sleek, minimalistic design incorporates a black finish and easily accessible controls, ensuring a seamless installation process. Additionally, the RCA input options provide compatibility with various sources, such as head units and processors.

Overall, the Rockford Fosgate Punch 45 stands out as a reliable amplifier that seamlessly blends power, versatility, and sound quality. Its combination of advanced features and user-friendly design makes it an excellent choice for anyone looking to enhance their vehicle's audio system. Whether you're a seasoned audiophile or just getting started, the Punch 45 offers the performance and durability needed to elevate your listening experience.
Top Page Image Contents