INSTALLATION

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

:If you feel unsure about installing this system yourself, have it installed by a CAUTION qualified technician.

:Before installation, disconnect the battery negative (-) terminal to prevent CAUTION damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide adequate cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

6

Page 5 Page 7
Page 6
Image 6
Rockford Fosgate T20001 BD manual Mounting Locations, Engine Compartment, Trunk Mounting, Passenger Compartment Mounting
Page 5 Page 7

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.
Top Page Image Contents