Rockford Fosgate T10001 BD, T20001 BD, T30001 BD manual Installation Considerations

Models: T20001 BD T30001 BD T10001 BD

1 72
Download 72 pages 44.08 Kb
Page 5
Image 5

 

DESIGN FEATURES

7.

Remote Bass – The Para-Punch Remote Bass connection is made with a RJ-45 cable and can be installed

 

in a variety of ways for easy control access. One control is used to boost low frequency information to

 

overcome road noise and put the bass in your face.This Bass control is a narrow band adjustment

 

variable from 0dB to +18dB with a Gyrator based Punch EQ that eliminates frequency shift with boost.

8.

The other control is used for adjusting center frequency variable from 35Hz to 70Hz.

Infrasonic Filt r – A 28Hz High Pass filter designed to prevent frequencies below the audio range

 

from being applied to the subwoofer from the amplifier. Consequently improving subwoofer

9.

performance and power handling, particularly in vented enclosures.

Gain Control – The input gain control is preset to match the output of most source units. It can be

10.

adjusted to match output levels from a variety of source units.

Variable Crossover – Is a built-in 24dB/octave Butterworth filter with a crossover point variable

11.

from 32Hz to 250Hz.The crossover is set to Low-Pass (LP).

Mode Switch – Used to set the amplifier between single, for single amplifier use, and Master or Slave

 

for when connecting multiple bd amplifiers together.The first amplifier in the series being set as

 

Master and the subsequent amplifiers being set as Slave.This allows one gain, crossover, infrasonic

12.

filter and bass boost setting for all slaved amplifiers.

Phase Switch – Used when bridging two bd amplifiers together using a bd Sync cable to phase one

13.

amplifier 180° from the other when driving a common load.

bd Sync Connect on – These amplifiers have a 6 pin mini DIN connector.When operating two

 

amplifiers together in a bridged mode, a bd Sync cable must be used.This will allow the two

14.

independent frequency carrier generators in each unit to be synchronized.

RCA Input Jacks – The industry standard RCA jacks provide an easy connection for signal level input.

15.

They are nickel-plated to resist the signal degradation caused by corrosion.

RCA Pass-Thru Jacks – The Pass-Thru provides a convenient source for daisy-chaining an additional

 

amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier

16.

location.

Remote Terminal – This heavy duty, platinum-plated wire connector will accept wire sizes from

 

12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when

17.

+12V DC is applied.

Power Terminals – The power and ground connectors on the amplifier are platinum-plated and will

 

accommodate up to 1/0 AWG wire maximizing the input current capability of the amplifier.

 

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter

Hand held drill w/assorted bits

Wire strippers

1/8" diameter heatshrink tubing

Wire crimpers

Assorted connectors

Wire cutters

Adequate Length—Red Power Wire

#2 Phillips screwdriver

Adequate Length—Remote Turn-on Wire

Battery post wrench

Adequate Length—Black Grounding Wire

5

Page 5
Image 5
Rockford Fosgate T10001 BD, T20001 BD, T30001 BD manual Installation Considerations

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.