INSTALLATION

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system.We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Power Series amplifier without problems, although battery and alternator life can be reduced slightly.To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

:If you do not feel comfortable with wiring your new unit, please see your CAUTION local Authorized Rockford Fosgate Dealer for installation.

:Before installation, disconnect the battery negative (-) terminal to prevent CAUTION damage to the unit, fire and/or possible injury.

:Avoid running power wires near the low level input cables, antenna, power CAUTION leads, sensitive equipment or harnesses.The power wires carry substantial

current and could induce noise into the audio system.

1. Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors.This is done to prevent coupling the noise from radiated electrical fields into the audio signal.When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2. Prepare the RED wire (power cable) for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE:The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and ensure connections are water tight.

3. Trim the RED wire (power cable) within 18" of the battery and splice in a inline fuse holder. See Specifications for the rating of the fuse to be used. DO NOT install the fuse at this time.

4. Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal.

5. Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bare wire into the GROUND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

NOTE:Keep the length of the BLACK wire (Ground) as short as possible. Always less than 30"(76.2cm). 6. Prepare the Remote turn-on wire for for attachment to the amplifier by stripping 5/8" of insulation

from the end of the wire. Insert the bared wire into the REMOTE terminal and tighten the set screw to secure the wire in place. Connect the other end of the Remote wire to a switched 12 volt positive source.The switched voltage is usually taken from the

source unit's remote amp on lead. If the source unit does

not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt

source to activate the amplifier.

7. Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or

plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle

stops.

7

Page 6 Page 8
Page 7
Image 7
Rockford Fosgate T30001 BD Installation Battery and Charging, Wiring the System, Source to activate the amplifier, Stops
Page 6 Page 8

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.
Top Page Image Contents