HP Z Virtual instruction

Install the FBWC module (Installing the flash-backed write cache module on page 49), if it is not already installed.

Hardware options installation

8. Connect the capacitor pack cable to the connector on the top of the cache module.

9. Install the access panel on page 20.

10. Install the server into the rack (Installing the server into the rack on page 35).

11.Connect each power cord to the server.

12. Connect each power cord to the power source.

13. Power up the server on page 18.

Installing the flash-backed write cache capacitor pack

CAUTION: The cache module connector does not use the industry-standard DDR3 mini-DIMMs. Do not use the controller with cache modules designed for other controller models, because the controller can malfunction and you can lose data. Also, do not transfer this cache module to an unsupported controller model, because you can lose data.

1. Back up all data.

2. Close all applications.

CAUTION: In systems that use external data storage, be sure that the server is the first unit to be powered down and the last to be powered back up. Taking this precaution ensures that the system does not erroneously mark the drives as failed when the server is powered up.

3.Power down the server on page 18.

4.Remove all power:

a.Disconnect each power cord from the power source.

b.Disconnect each power cord from the server.

5.Extend the server from the rack on page 19.

6.Remove the access panel on page 20.

7.

50 Chapter 5

Image 56

HP Z Virtual manual Installing the flash-backed write cache capacitor pack

Contents

HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Component identification Front panel components Front panel LEDs and buttons Description Status Access the Systems Insight Display Systems Insight Display LEDs Systems Insight Display LED combinations RJ-45 LEDs for status Rear panel LEDs and buttonsPage Rear panel components Rear panel LEDs and buttons Non-hot-plug PCI riser board slot definitions FL/FH System board components ItemDescription System maintenance switch Default Function NMI functionality Dimm slot locations SAS and Sata device numbers Hot-plug drive LED definitions LED PCI riser cage LED Fbwc module LEDs P420 Amber Green Interpretation Hot-plug fans Page Operations Power up the serverPower down the server Extend the server from the rack Remove the access panel Install the access panel Access the product rear panel Opening the cable management arm Power down the server on Remove the hot-plug fan cage Remove the access panel on Remove the hot-plug fan Remove the full-length expansion board Remove the PCI riser cage Install the PCI riser cage Install the access panel on Secure the full-length expansion board retainer Remove the air baffle Page Setup Optional installation services Optimum environment Space and airflow requirements Electrical grounding requirements Temperature requirementsPower requirements Connecting a DC power cable to a DC power source Rack warnings Identifying the contents of the server shipping cartonInstalling hardware options Installing the server into the rack Page VMware vSphere Installing the operating systemCitrix XenServer Powering on and selecting boot options Registering the server Memory options Hardware options installationIntroduction HP SmartMemory Memory subsystem architecture Single-, dual-, and quad-rank DIMMs Dimm identification Memory configurations 1Maximum capacity Advanced ECC memory configuration General Dimm slot population guidelines Advanced ECC population guidelines Installing a Dimm Lockstep Memory population guidelines Power up the server on Hot-plug hard drive options Installing a hot-plug SAS or Sata hard drive Controller options Removing a hot-plug SAS or Sata hard drive Installing the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Expansion board options Removing the expansion slot blanksPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage 2U rack bezel option HP Trusted Platform Module option Installing the Trusted Platform Module board HP Trusted Platform Module option Retaining the recovery key/password Enabling the Trusted Platform Module Cabling SAS hard drive cabling Optical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option HP product QuickSpecs Software and configuration utilitiesServer mode HP iLO Management Engine HP iLO Intelligent Provisioning Integrated Management Log HP Insight Remote Support software Erase Utility Scripting Toolkit HP Service Pack for ProLiant HP Smart Update Manager HP ROM-Based Setup Utility Using Rbsu Configuring AMP modes Auto-configuration processBoot options Re-entering the server serial number and product ID Utilities and featuresArray Configuration Utility HP Smart Storage Administrator Option ROM Configuration for Arrays Automatic Server Recovery ROMPaq utility Keeping the system current USB supportRedundant ROM support Drivers Software and firmware Version control Change control and proactive notification Troubleshooting Troubleshooting resources Battery replacement Locate the battery System board components onPage Specifications Environmental specificationsMechanical specifications Power supply specifications HP 1200 W CS HE Power Supply 94% efficiency Specification Value Input requirements HP contact information Support and other resourcesBefore you contact HP Customer Self Repair Acronyms and abbreviations 101 Acronyms and abbreviations Documentation feedback Index ASR IML