HP Z Virtual manual

7. Replace the safety cover.

8. Insert the power supply into the power supply bay until it clicks into place.

9.Route the power cord. Use best practices when routing power cords and other cables. A cable management arm is available to help with routing. To obtain a cable management arm, contact an HP authorized reseller.

10.Make sure the 48V DC power source is off or the PDU breaker is in the off position, and then connect the power cord to the 48V DC power source or PDU.

11.Turn on the 48V power source or switch the PDU breaker to the on position to supply 48V to the power supply.

12.Be sure that the green power supply LED is on.

48V DC power supply option 59

Page 65

Image 65

Contents

HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Front panel components Component identification Description Status Front panel LEDs and buttons Systems Insight Display LEDs Access the Systems Insight Display RJ-45 LEDs for status Rear panel LEDs and buttons Systems Insight Display LED combinationsPage Rear panel components Non-hot-plug PCI riser board slot definitions Rear panel LEDs and buttons FL/FH ItemDescription System board components Default Function System maintenance switch Dimm slot locations NMI functionality LED SAS and Sata device numbers Hot-plug drive LED definitions PCI riser cage LED Amber Green Interpretation Fbwc module LEDs P420 Hot-plug fans Page Operations Power up the serverPower down the server Extend the server from the rack Install the access panel Remove the access panel Opening the cable management arm Access the product rear panel Remove the hot-plug fan cage Power down the server on Remove the hot-plug fan Remove the access panel on Remove the full-length expansion board Remove the PCI riser cage Install the access panel on Install the PCI riser cage Secure the full-length expansion board retainer Remove the air baffle Page Optional installation services Setup Space and airflow requirements Optimum environment Electrical grounding requirements Temperature requirementsPower requirements Connecting a DC power cable to a DC power source Rack warnings Identifying the contents of the server shipping cartonInstalling hardware options Installing the server into the rack Page VMware vSphere Installing the operating systemCitrix XenServer Registering the server Powering on and selecting boot options Memory options Hardware options installationIntroduction Memory subsystem architecture HP SmartMemory Dimm identification Single-, dual-, and quad-rank DIMMs 1Maximum capacity Memory configurations Advanced ECC memory configuration Advanced ECC population guidelines General Dimm slot population guidelines Lockstep Memory population guidelines Installing a Dimm Hot-plug hard drive options Power up the server on Installing a hot-plug SAS or Sata hard drive Removing a hot-plug SAS or Sata hard drive Controller options Installing the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Removing the expansion slot blanks Expansion board optionsPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage HP Trusted Platform Module option 2U rack bezel option Installing the Trusted Platform Module board HP Trusted Platform Module option Enabling the Trusted Platform Module Retaining the recovery key/password SAS hard drive cabling Cabling Optical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option HP product QuickSpecs Software and configuration utilitiesServer mode HP iLO HP iLO Management Engine Integrated Management Log Intelligent Provisioning Erase Utility HP Insight Remote Support software Scripting Toolkit HP Smart Update Manager HP Service Pack for ProLiant Using Rbsu HP ROM-Based Setup Utility Configuring AMP modes Auto-configuration processBoot options Re-entering the server serial number and product ID Utilities and featuresArray Configuration Utility Option ROM Configuration for Arrays HP Smart Storage Administrator ROMPaq utility Automatic Server Recovery USB support Keeping the system currentRedundant ROM support Drivers Software and firmware Version control Change control and proactive notification Troubleshooting resources Troubleshooting Locate the battery System board components on Battery replacementPage Environmental specifications SpecificationsMechanical specifications Power supply specifications Specification Value Input requirements HP 1200 W CS HE Power Supply 94% efficiency HP contact information Support and other resourcesBefore you contact HP Customer Self Repair 101 Acronyms and abbreviations Acronyms and abbreviations Documentation feedback ASR Index IML