Remove the air baffle on | HP Z Virtual specs

5. Release the full-length expansion board retainer, and then remove the PCI riser cage.

6. Remove the air baffle on page 28

7. Remove the fan cage.

8. Disconnect any SAS cables from the hard drive cage and either the embedded SAS controller or an optional SAS controller. Do not disconnect the power cable.

Chipset SATA cable option 77

Image 83

HP Z Virtual manual Remove the air baffle on

Contents

HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Front panel components Component identification Description Status Front panel LEDs and buttons Systems Insight Display LEDs Access the Systems Insight Display RJ-45 LEDs for status Rear panel LEDs and buttons Systems Insight Display LED combinationsPage Rear panel components Non-hot-plug PCI riser board slot definitions Rear panel LEDs and buttons FL/FH ItemDescription System board components Default Function System maintenance switch Dimm slot locations NMI functionality LED SAS and Sata device numbers Hot-plug drive LED definitions PCI riser cage LED Amber Green Interpretation Fbwc module LEDs P420 Hot-plug fans Page Operations Power up the serverPower down the server Extend the server from the rack Install the access panel Remove the access panel Opening the cable management arm Access the product rear panel Remove the hot-plug fan cage Power down the server on Remove the hot-plug fan Remove the access panel on Remove the full-length expansion board Remove the PCI riser cage Install the access panel on Install the PCI riser cage Secure the full-length expansion board retainer Remove the air baffle Page Optional installation services Setup Space and airflow requirements Optimum environment Electrical grounding requirements Temperature requirementsPower requirements Connecting a DC power cable to a DC power source Rack warnings Identifying the contents of the server shipping cartonInstalling hardware options Installing the server into the rack Page VMware vSphere Installing the operating systemCitrix XenServer Registering the server Powering on and selecting boot options Memory options Hardware options installationIntroduction Memory subsystem architecture HP SmartMemory Dimm identification Single-, dual-, and quad-rank DIMMs 1Maximum capacity Memory configurations Advanced ECC memory configuration Advanced ECC population guidelines General Dimm slot population guidelines Lockstep Memory population guidelines Installing a Dimm Hot-plug hard drive options Power up the server on Installing a hot-plug SAS or Sata hard drive Removing a hot-plug SAS or Sata hard drive Controller options Installing the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Removing the expansion slot blanks Expansion board optionsPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage HP Trusted Platform Module option 2U rack bezel option Installing the Trusted Platform Module board HP Trusted Platform Module option Enabling the Trusted Platform Module Retaining the recovery key/password SAS hard drive cabling Cabling Optical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option HP product QuickSpecs Software and configuration utilitiesServer mode HP iLO HP iLO Management Engine Integrated Management Log Intelligent Provisioning Erase Utility HP Insight Remote Support software Scripting Toolkit HP Smart Update Manager HP Service Pack for ProLiant Using Rbsu HP ROM-Based Setup Utility Configuring AMP modes Auto-configuration processBoot options Re-entering the server serial number and product ID Utilities and featuresArray Configuration Utility Option ROM Configuration for Arrays HP Smart Storage Administrator ROMPaq utility Automatic Server Recovery Drivers Keeping the system currentUSB support Redundant ROM support Software and firmware Version control Change control and proactive notification Troubleshooting resources Troubleshooting Locate the battery System board components on Battery replacementPage Power supply specifications SpecificationsEnvironmental specifications Mechanical specifications Specification Value Input requirements HP 1200 W CS HE Power Supply 94% efficiency HP contact information Support and other resourcesBefore you contact HP Customer Self Repair 101 Acronyms and abbreviations Acronyms and abbreviations Documentation feedback ASR Index IML