Manuals / Brands / Power Tools / Laminate Trimmer / Roland / Power Tools / Laminate Trimmer

Roland CX-24/12 12-3 Uncut Areas Remain, or Areas Are Not Cleanly Cut, 12-4 The Results of Cutting Are Displaced, and Uncut Portions Remain

1 75

Download 75 pages, 839.62 Kb

67

12 What to do if...

12-3 Uncut Areas Remain, or Areas Are Not Cleanly Cut

Are the blade and blade holder securely mounted?

Install these so that there is no looseness .

The blade may be broken.

Replace with a new blade.

Is there any buildup of dust or material adhesive on the tip of the blade?

Check if there are any dirty deposits on the blade. If dirty, remove and clean the blade.

Is there any buildup of pieces of material or dust inside the blade holder?

Take off the tip of the blade holder and remove any pieces of material inside.

Is the amount of blade extension correct?

If the setting for the amount of blade compensation is not correct for the blade, corners may be rounded or have horns.

Refer to "4-7 Performing a Cutting Test - Adjusting the Amount of Blade Extension."

Are the blade force and cutting speed appropriate for the material being cut?

Perform a cutting test and use the display menu to make the settings for suitable values.

Refer to "4-7 Performing a Cutting Test - Adjusting the Blade Force."

Is the blade protector damaged or deformed?

If material is not cut properly even though the CX-24/12 settings are correct and the blade and cutter holder are installed correctly, the

blade protector may be damaged. If this happens, contact your authorized Roland DG Corp. dealer or service center. (Replacement is a

charged service operation.)

12-4 The Results of Cutting Are Displaced, and UncutPortions Remain

Is a thick material being used?

When using a thick material, change the display menu setting from "WEIGHT" to "HEAVY."

When performing cutting using roll material, was the amount of material to be cut pulled out before performing cutting.

When the material is pulled out while cutting is being performed, the material may slip or operation may stop due to a motor error.

Contents

Main CX-24/12 USERS MANUAL Contents To Ensure Safe Use About and Notices About the Symbols Page About the Labels Affixed to the Unit Avis sur les avertissements propos des symboles Pour utiliser en toute scurit Page propos des tiquettes colles sur l'appareil 1 Checking Supplied Items 2 Part Names and Functions 2-1 Front View 2-2 Rear View 2-3 Operation Panel 3 Preparing the CX-24/12 3-1 Setting 3-2 Connection For IBM PC or PC Compatibles For Macintosh 3-3 Installing the Driver Connecting the Power Cord 3-4 Port Setting Checking the Communication Parameters for the Port and Driver - Windows 95/98/Me 2 Checking the Communication Parameters for the Port and Driver - Windows NT 4.0/2000/XP 5 Turned clockwise Turned coun- terclockwise Making the Settings from the Menu on the CX-24/12 Page 4 4-2 Loading the Material Acceptable Material Sizes - CX-24 Loading the Material - If You Are Not Using the Roller Base - If You Are Using the Roller Base Page 4-3 Turning on the Power For the CX-24: Putting the Machine in the Setup State SELECT | ROLL Making Menu Settings with the Control Panel How to View the Display For the CX-12: SETUP -> ENTER 4-4 Checking Material Feed AREA |< 1.0m> AREA | < 1.0m> AREA | MOVE 4-5 When Performing Long Cutting 1.5 m (59 in.) or more Location of the origin point Material shape selected from the menu Model 4-6 Setting the Origin Point ORIGIN SET 4 4-7 Performing a Cutting Test (How to Adjust Blade Force/Adjusting the Cutter Blade) The square should remain, without peeling off. Cutting Test Adjusting the Amount of Blade Extension Adjusting the Blade Force Too large Too small FORCE | < 80g> FORCE | < 80g> 4-8 Downloading Cutting Data NOTICE :Cutting area :Pinch roller Page Page Pausing Cutting Operations PAUSE | <CONT.> - To resume cutting without change 8 9 11 10 Page Page - For Roll Materials, or When Detaching Only a Cut Portion 4-10 When Cutting Is Completed When not in use for extended periods, unplug the power cord from the electrical outlet. Page 5 6 Plotting on Paper Media OFFSET| <0(PEN)> Acceptable Pens and Paper Media 7 Repeating the Same Cutting Preparing the Cutting Data REPLOT| START REPLOT| CLEAR Page 10 mm (0.39 in.) 8 Cutting Printed Material 8-2 Shape and Layout of Crop Marks Shape of Crop Marks 8-1 Using Crop Marks - Data-creation Program 8-3 Loading the Material Page 9 10 7 8 Page 7 CROPMARK|<AUTO> CX-24 CX-12 BASE X|<5.0mm> WIDTH |<170mm> LENGTH|<210mm> 9 10 1 2 5 6 7 3 4 8 9 10 MARK 1 NOT FOUND 8-5 When Crop Marks Cannot Be Read MARK 2 NOT FOUND 8-6 When the Printing and Cutting Locations Are Misaligned MEDIA MISALIGN ANGLE TOO BIG WIDTH TOO BIG ANGLE TOO BIG 9-1 Blade and Material Combinations 9 About the Blades and Materials 9 About the Blades and Materials Acceptable Material Widths * Make sure the pinch rollers are positioned above the grit rollers. CX-12 9-2 About the Materials CX-24 About the Cutting Area <CX-24> <CX-12> When Loading Flat Material Rubber Sandblast Stencils A Material with Edge Holes for Sprocket Feed 10-1 How to Read This Chapter 10 Display Menu Descriptions SELECT SELECT | ROLL 10-2 Display Menu Descriptions CROPMARK| <OFF> CROPMARK BASE Y | <5mm> BASE X | <5mm> BASE X BASE Y WIDTH SETUP | <ON> LENGTH | <210mm> LENGTH SETUP FORCE SPEED AREA |< 1.0m> SPEED |<40cm/s> AREA OFFSET REPLOT SMOOTH.| <ON> ROTATE| <OFF> SMOOTH ROTATE WEIGHT I/O | <AUTO> RESTORE| <USER1> I/O CALL| <USER1> #BAUD. #HANDS.|<H-WIRE> #PARITY| <NONE> #HANDS. #STOP.| <1> LANG. INITIALIZE EEROM DEMO CUT INITIALIZE EEROM UNIT | <Metric> 11 Display Menu Flowchart Display Menu Flowchart When Using Crop Marks 12 What to Do If... 12-1 If the CX-24/12 Doesn't Run... SELECT | ROLL SETUP -> ENTER PAUSE | <CONT> To stop operation 12-2 The Material Slips Away from the Pinch Rollers During the Cutting Process 12-3 Uncut Areas Remain, or Areas Are Not Cleanly Cut 12-4 The Results of Cutting Are Displaced, and Uncut Portions Remain 12-5 Error Messages Err:Bad Positin SHEET UNLOADED DATA OVERFLOW DATA EMPTY Origin Error Page 13 Instruction Support Chart 14 Specifications * Parallel Serial Parallel connector (in compliance with specifications of Centronics) Serial connector (RS-232C) Index A B C D R S T U W