Manuals / Rose electronic / Computer Equipment / Switch

Rose electronic Vista Mini operation manual Appendix A. Factory Default Settings

Models: Vista Mini

1 24

Download 24 pages 46.22 Kb

Page 22

APPENDIX A. FACTORY DEFAULT SETTINGS

Setting	Default

Scan enable	Off

Scan Time Interval	5 seconds

Caps/Numlock/Scroll	Numlock On

Keyboard Mode	2

Typematic Value	43 (Rate=10.9 chars/sec, delay = 500 millisec.)

Mouse translation	0 (PS/2 mouse input to PS/2 mouse output)

APPENDIX B. GENERAL SPECIFICATIONS

SIZE	.8" high by 3.2" wide by 4.2" deep

WEIGHT	1 lb.

ENVIRONMENT	0 to 55°C., 0% to 80% non-condensing
	relative humidity

INPUT POWER	Supplied by computers

CPU CONNECTORS	KVT-2U	DB25 Female
	KVT-2PC	HD15F/MD6F/MD6F/3.5 mm
		jack

VIDEO CONNECTOR	HD15 female VGA video

PS/2 MOUSE CONNECTOR	Mini-din 6 female

KEYBOARD CONNECTOR	Mini-din 6 female

AUDIO CONNECTOR	3.5 mm stereo jack

CHASSIS	Fully shielded, black painted steel

18	VIStA MINI INSTALLATION AND OPERATION MANUAL

Image 22

Rose electronic Vista Mini operation manual Appendix A. Factory Default Settings, Appendix B. General Specifications

Contents

DESKTOP KVM SWITCH WITH AUDIO E L E C T R O N I C SInstallation and Operation Manual VISTA MINILIMITED WARRANTY KEYBOARD COMMAND SUMMARY TROUBLESHOOTING SERVICE INFORMATION TABLE OF CONTENTSINSTALLATION VIStA MINI HARDWARECables and accessories Factory default settingsGeneral specifications Appendix AVIStA MINI INSTALLATION AND OPERATION MANUAL FEATURESINTRODUCTION Vista Mini models Package contentsGETTING STARTED Locating the unitCables for use with models that have PC connectors VIStA MINI INSTALLATION AND OPERATION MANUALCables for use with models that have DB25 connectors To Two ViewVIStA MINI INSTALLATION AND OPERATION MANUAL VIStA MINI HARDWAREThe front panel RESET SWITCHThe connectors VIStA MINI INSTALLATION AND OPERATION MANUALStep 2. Connecting the computers INSTALLATIONStep 1. Connecting monitor, keyboard, and mouse For Vista Mini models with DB 25 connectorsStep 4. Switching from the keyboard Step 3. Powering up the systemVIStA MINI INSTALLATION AND OPERATION MANUAL Keyboard computer selection Scan mode commandsOPERATION Going to the other computerTypematic value command Scan time interval commandMode command VIStA MINI INSTALLATION AND OPERATION MANUALwhen holding a key down to repeat the key, such as when moving a cursor across a line. The rate is the speed at which the keys are sent in keys/second. The delay is the wait time in milliseconds after the key is initially pressed, before additional keystrokes are sent. To issue the command press and release the left Control key, then type “A”, then enter the 1-3 digit decimal typematic value followed by Enter. The typematic value is defined as shown below. Use the keep command to save the value PS/2 to serial mouse translation, wheel mouse Keep commandNull command VIStA MINI INSTALLATION AND OPERATION MANUALReset computer mouse command ROM Identification commandReset command Reset to factory defaultVIStA MINI INSTALLATION AND OPERATION MANUAL Key Sequence KEYBOARD COMMAND SUMMARYCommand DescriptionVIStA MINI INSTALLATION AND OPERATION MANUAL Enter3. Can’t switch ports from keyboard TROUBLESHOOTING1. CPU does not boot, keyboard error received 2. Mouse driver does not load9. Lower resolution video OK, but can’t enter high resolution mode SERVICE INFORMATIONMaintenance and repair 6. PS/2 mouse gets out of syncSetting APPENDIX A. FACTORY DEFAULT SETTINGSAPPENDIX B. GENERAL SPECIFICATIONS DefaultVIStA MINI INSTALLATION AND OPERATION MANUAL APPENDIX C. CABLESPart Number CPU adapter cables for models with DB25 connectorsE L E C T R O N I C S