Rotel RC-06 owner manual AC Power and Control, Remote Sensor, A Few Precautions, Placement, Cables

RC-06Stereo Control Amplifier

Remote Sensor 5

The Remote Sensor picks up the infrared signals from the remote control. Do not cover or block the sensor. It must be unobstructed or the remote control will not work properly. The operation of the Remote Sensor can also be affected if it is exposed to bright light, particu- larly sunlight. Certain types of lighting, such as halogen lights, that emit a fair amount of infrared light, can also interfere with proper operation. In addition remote control functions may not work reliably if the batteries in the RR-AT94 are weak.

A Few Precautions

WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnect- ing the loudspeakers or any associated com- ponents. Do not turn the system components back on until you are sure all the connec- tions are correct and secure. Pay particular attention to the speaker wires. There must be no loose strands that could contact the other speaker wires, or the chassis of the amplifier.

Please read this manual carefully. It provides information on how to incorporate the RC-06 into your system as well as information that will help you get optimum sound performance. Please contact your authorized Rotel dealer for answers to any questions you might have. In addition, all of us at Rotel welcome your questions and comments.

Save the RC-06 shipping carton and all en- closed packing material for future use. Shipping or moving the RC-06 in anything other than the original packing material may result in severe damage to your amplifier.

Fill out and send in the owner’s registration card packed with the RC-06. Also be sure to keep the original sales receipt. It is your best record of the date of purchase, which you will need in the event warranty service is ever required.

6

Placement

Like all audio components that handle low- level signals, the RC-06 can be affected by its environment. Avoid placing the RC-06 on top of other components. Also avoid routing audio signal cables near power cords. This will minimize the chance it will pick up hum or interference.

The RC-06 generates heat as part of its normal operation. The heat sinks and ventilation open- ings in the amplifier are designed to dissipate this heat. The ventilation slots in the top cover must be open. There should be 10 cm (4 inches) of clearance around the chassis, and reason- able airflow through the installation location, to prevent the amplifier from overheating.

Remember the weight of the amplifier when you select an installation location. Make sure that the shelf or cabinet can support it. We recommend installing the RC-06 in furniture designed to house audio components. Such furniture is designed to reduce or suppress vibration which can adversely affect sound quality. Ask your authorized Rotel dealer for advice about component furniture and proper installation of audio components.

Cables

Be sure to keep the power cords, digital signal cables and regular audio signal cables in your installation away from each other. This will minimize the chance of the regular audio signal cables picking up noise or interference from the power cords or digital cables. Using only high quality, shielded cables will also help to prevent noise or interference from degrad- ing the sound quality of your system. If you have any questions see your authorized Rotel dealer for advice about the best cable to use with your system.

AC Power and Control

AC Power Input y

The RC-06 does not draw high levels of current from the power outlet. However, whenever pos- sible, it should be plugged directly into a 2-pin polarized wall outlet. Do not use an extension cord. A heavy duty multi-tap power outlet strip may be used if it (and the wall outlet) can handle the current demanded by the RC-06 and all the other components connected to it.

Your RC-06 is configured at the factory for the proper AC line voltage in the country where you purchased it (either 120 volts AC or 230 volts AC with a line frequency of either 50 Hz or 60 Hz). The AC line configuration is noted on a decal on the back panel.

NOTE: Should you move your RC-06 amplifier to another country, it is possible to reconfigure it for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the enclosure of the RC-06 exposes you to dangerous voltages. Consult a qualified service person or the Rotel factory service department for information.

If you are going to be away from home for an extended period of time such as a month-long vacation, it is a sensible precaution to unplug your amplifier (as well as other audio and video components) while you are away.

Power/Standby Switch 1o and Power Indicator 2

The Power Indicator light above the Standby button is lit whenever the RC-06 is connected to a live AC outlet. When the front panel Standby button or the remote control Power button is pressed the RC-06 is turned on. When the RC-06 is on the Function indicator and the Volume control are illuminated. Pressing either button again puts the RC-06 in standby mode and turns off the Volume and Function illumination.

See the “12V Trigger Outlet” section for more information on ways you may be able to turn on and off other components in your system along with the RC-06.