Stereo/Bridged Mono Mode Selection

It is useful to think of the RMB-1066 as three stereo amplifiers in a single chassis. Each of the three pair of amplifier channels can be operated in Stereo or Bridged Mono mode.

•Stereo mode: Conventional 2-channel stereo operation for a pair of amplifier channels. Minimum speaker load: 4 ohms.

•Bridged Mono mode: Bridged Mono mode more than doubles the power into a single speaker. Minimum speaker load: 8 ohms.

The two modes are selected by three rear panel switches, one for each pair of channels. Ste- reo or Bridged Mono configuration is inde- pendent for each pair of channels. You can configure some pairs of channels in Stereo mode and others in Bridged Mono mode.

Input Select Switches Bridged Mono LEDs

A rear panel switch adjacent to the inputs selects Stereo mode or Bridged Mono mode for each of the three pair of amplifier chan- nels.

For Stereo mode: Slide the switch asso- ciated with the desired pair of amplifier chan- nels to the right, use both LEFT and RIGHT input connectors, and connect one speaker to each pair of speaker connectors.

NOTE: For groups “B” and/or “C”, you can also place the INPUT SELECT switch in the center LINK position for Stereo mode. This routes the input signals from the “A” group to the inputs for that pair of ampli- fier channels.

For Bridged Mono mode: Slide the switch to the left, use only the LEFT INPUT connec- tion, and connect only one speaker to the two outer speaker connectors. The BRIDGED MONO LED will light to indicate Bridged Mono mode.

7

Signal Connections

The RMB-1066 provides standard conven- tional input connections — unbalanced RCA type connections as found on nearly all au- dio equipment.

There is also a pair of SIGNAL OUTPUT LINK connections for passing the input signal con- nected to the “A” pair of channels on to an- other audio component. Additionally, the input signal to the “A” pair of channels can be automatically linked to the inputs for the “B” and/or “C” channels, so that a separate in- put signal cable is not required for those chan- nels, for example in large systems where the RMB-1066 is being used to drive multiple pairs of speakers in stereo mode.

RCA Inputs

See Figures 2 and 3

There are two RCA inputs for each of the three pair of amplifier channels. These RCA inputs accept audio signals from preamplifiers or surround sound processors. Use high qual- ity audio interconnect cables for best perfor- mance.

NOTE: You can link the inputs for group “A” to groups “B” and/or “C” by placing the INPUT SELECT switch in the center LINK position. No input connection is required for that group. Placing the switch in this position leaves that pair of channels in Ste- reo mode.

For Bridged Mono operation, use only the LEFT INPUT for that pair of amplifier chan- nels. Connect one output channel of your preamp to the LEFT INPUT on the RMB-1066. Make sure that the INPUT SELECT SWITCH selector switch is in the BRIDGED position.

Input Level Controls

Three controls on the front panel, one for each pair of amplifier channels, provide input level adjustments. These allow you to adjust the gain of the amplifiers to match other components in an elaborate system.

Use a small flat blade screwdriver to turn the control clockwise to increase gain. Turn the control counterclockwise to reduce gain.

English

Signal Output Link

This pair of RCA connections can be used to pass unprocessed input signals to another audio component, for example to “daisy- chain” an additional amplifier to drive a sec- ond set of speakers.

The input signals connected to the “A” inputs are always available at SIGNAL OUTPUT LINK connections. These input signals can also be linked to the “B” and/or “C” inputs by play- ing the INPUT SELECT switch associated with that pair of inputs in the LINK position.

Speakers

The RMB-1066 has three groups of speaker connectors, one for each pair of amplifier channels. These can be used to connect two loudspeakers in Stereo mode, or to connect one loudspeaker in Bridged Mono mode.

Speaker Selection

The nominal impedance of the loudspeaker(s) connected to the RMB-1066 in the various operating modes should be:

•Stereo mode: minimum 4 ohms

•Bridged Mono mode: minimum 8 ohms When driving multiple pairs of speakers connected in parallel to a single amplifier channel, the effective impedance the am- plifier sees is cut in half. For example, when driving two 8 ohm speakers, the amplifier sees a 4 ohm load. When driving multiple speakers in parallel, select speakers with a nominal impedance of 8 ohms or higher.

Speaker Wire Selection

Use insulated two-conductor stranded wire to connect the RMB-1066 to the speakers. The size and quality of the wire can have an au- dible effect on the performance of the system. Standard speaker wire will work, but can re- sult in lower output or diminished bass re- sponse, particularly over longer distances. In general, heavier wire will improve the sound. For best performance, you may want to con- sider special high-quality speaker cables. Your authorized Rotel dealer can help in the se- lection of appropriate cables for your system.

Page 6 Page 8
Page 7
Image 7
Rotel RMB-1066 owner manual Speakers
Page 6 Page 8

RMB-1066 specifications

The Rotel RMB-1066 is a powerful and versatile six-channel power amplifier that has made a significant impression on both home theater enthusiasts and audiophiles. Designed with meticulous attention to detail, this amplifier combines advanced technologies to deliver superb sound quality and reliability. One of the most notable features of the RMB-1066 is its robust power output, delivering 100 watts per channel into 8 ohms, and 200 watts into 4 ohms. This ample power ensures that it can drive a range of speakers effectively, making it an excellent choice for both surround sound systems and multi-room audio setups.

The RMB-1066 boasts a Class AB amplifier design, which is renowned for its ability to provide the warmth and richness of sound that many listeners crave, while maintaining high efficiency. This design minimizes distortion levels, ensuring that audio playback remains clean and detailed across various music genres and movie soundtracks. Another significant characteristic of the Rotel RMB-1066 is its high-current capability, which allows it to deliver dynamic peaks without sacrificing performance, ensuring that your audio experience is always engaging and impactful.

Rotel's commitment to quality extends to its build as well. The amplifier features a robust, all-aluminum chassis that not only adds to its aesthetic appeal but also helps in minimizing resonance and interference. The inclusion of a toroidal transformer further enhances its performance by providing a stable power supply, enabling the amplifier to handle demanding loads with ease.

Additionally, the RMB-1066 is equipped with an array of input options, including both balanced and unbalanced inputs. This flexibility allows users to integrate the amplifier into their existing audio systems without complications. The rear panel also features speaker binding posts that can accommodate a variety of cable types and sizes, ensuring a secure and reliable connection.

In terms of connectivity, the Rotel RMB-1066 is designed with ease of use in mind, including a 12V trigger input that allows for automated operation alongside compatible components. This feature is particularly handy in custom installations where the convenience of automation can enhance the user experience.

Overall, the Rotel RMB-1066 stands out as an exemplary power amplifier that embodies high-performance audio reproduction, flexibility, and build quality, making it an ideal choice for anyone looking to elevate their home theater or audio setup to new heights.
Top Page Image Contents