![](/images/new-backgrounds/1213953/21395319x1.webp)
RZ 2610955525
THE DRYWALL ROUTER ONLY COUNTER- CLOCKWISE to take advantage of the “hugging” action of the bit along the contours of the template. Remember to use a smooth, continuous motion. The exception to this rule
applies to cutting window and door openings. Since you are tracing around the inside of the framing members, move the bit clockwise to take advantage of the bits “hugging” action.
|
|
| Maintenance | |
|
|
| Service | rotating it |
! | WARNING | Preventive maintenance | not to lose the screw. | |
|
| performed by unauthorized | 3. Using your fingernail, pry the brush door | |
personnel may result in misplacing of | loose and remove it from the tool. | |||
internal wires and components which could | 4. In order to remove the brush, you must pull | |||
cause serious hazard. We recommend that | back the spring that is holding the brush in | |||
all tool service be performed by a | place. Using needle nose pliers, carefully pull | |||
Rotozip/Bosch Factory Service Center or | back the end of the brush spring and place it to | |||
Authorized Rotozip/Bosch Service Station. | the side of the brush near the hole for the | |||
|
| TOOL LUBRICATION | brush door screw. Once the spring has been | |
Your Rotozip tool has been properly lubricated | moved, you can remove the brush by pulling | |||
and is ready to use. | on the brush wire connector (Fig. 11). Be | |||
|
|
| BEARINGS | careful not to bump the brush spring or |
After about | damage the brush wire connector. Make a | |||
every second brush change, the bearings | note of which side of the tool the brush was | |||
should be replaced at Bosch Factory Service | removed. | |||
Center or Authorized Bosch Service Station. | BRUSH | |||
Bearings which become noisy (due to heavy |
| |||
load or very abrasive material cutting) should | WIRE | |||
be replaced at once to avoid overheating or | CONNECTOR | |||
motor failure.CARBON BRUSHES | ||||
|
|
|
| BRUSH WIRE |
The brushes and commutator in your tool have |
| |||
been engineered for many hours of | FIG. 11 | |||
dependable service. To maintain peak motor |
| |||
efficiency, we recommend the brushes be |
| |||
examined every two to six months. Only use |
| |||
genuine | Rotozip replacement brushes |
| ||
specially designed for your tool. | SPRING | |||
If your tool runs sporadically, loses power, | SCREW HOLE | |||
makes unusual noises, or runs at a reduced |
| |||
speed, check the brushes. Continuing to use | 5. Check both brushes. The brushes in your | |||
the tool in this condition will permanently | ||||
damage the motor. | Drywall Router will not wear at the same rate. | |||
Do not attempt to operate the tool with | If either brush is less than 3/16" (4.8mm) long | |||
broken, missing, or loose brush doors. If | or the worn end of the brush is rough or pitted, | |||
the brush doors or brush door screws become | replace both brushes. Place the new brush in | |||
lost or damaged, please contact Rotozip | the brush holder, making sure the brush wire is | |||
Customer Service for replacement parts. | securely connected to its terminal inside the | |||
To Replace the Brushes | tool. Fold the brush wire away from the screw | |||
hole as shown. Place the end of the spring into | ||||
1. Disconnect the tool from the power supply. | its original position. | |||
2. Each door is held in place by a screw. | 6. Replace the brush doors. Be careful not to | |||
Using a screwdriver, loosen the screw by |