Manuals / Runco / Home Audio / Home Theater System

Runco LS-7 operation manual 1.Troubleshooting Chart continued, Maintenance and Troubleshooting

Models: LS-7

1 100

Download 100 pages 33.98 Kb

Page 79

Maintenance and Troubleshooting

Table 5-1. Troubleshooting Chart (continued)

Symptom	Possible Cause(s)	Solution

Colors in the image are	• The Red/Pr, Green/Y or	• Ensure that the source
swapped; for example, reds	Blue/Pb outputs from the	outputs are connected to
appear blue or vice versa.	source are connected to	the correct LS-7 input.
	the wrong inputs on the
	LS-7.

LED is flashing alternating	• The lamp cover is open.	• Close the lamp cover.
green and red.	• The lamp has failed or	• Replace the lamp with a
	exceeded its usage life.	new one.

LED is flashing red.	• LS-7 internal temperature	• Power off the LS-7 and
	is too high.	allow it to cool down.
		Ensure that the intake and
		exhaust vents are not
		blocked. Turn the
		projector back on. If the
		problem persists, please
		contact Runco Technical
		Support for assistance.

LED lights solid red.	• Fans are not working	• Please contact Runco
	properly or power-on	Technical Support for
	self-test has failed (Note).	assistance.

Note: You can obtain more detailed information about the cause of the error condition using
RS-232 commands. Refer to RS-232 Error Codes on page 76 for more information.

Runco LS-7 Installation/Operation Manual

63

Image 79

Runco LS-7 operation manual 1.Troubleshooting Chart continued, Maintenance and Troubleshooting

Contents

Home Theater Projector LS-7Page Length of Warranty RuncoCare Standard Two Year Limited WarrantyRuncoCare Standard Features Warranty CoverageWarranty Exclusions RuncoCare Claim ProcedureOnline Product Registration Extended Service OptionsLimitation of Implied Warranties Effect of Local Law Exclusion of DamagesCOPYRIGHT AND TRADEMARKS Important Safety Instructions DECLARATION OF CONFORMITY Compliance InformationIMPORTANT RECYCLE INSTRUCTIONS FCC PARTINDUSTRY CANADA ICES-003 PRODUCT DISPOSALPage RuncoCare Standard Two Year Limited Warranty Table of Contentsviii Floor Mounting Upright RS-232Error Codes Serial Command SyntaxKey Commands Operations CommandsTable of Contents List of Figures List of Figures If You Have Comments 1. Introduction1.1 About This Manual Target AudienceDANGER 1.2 Using This ManualOptional Accessories 1.3 Description, Features and BenefitsKey Features and Benefits Parts List Introduction MENU 2. Controls and Functions2.1 LS-7at a Glance SOURCEFRONT IR SENSOR EXHAUST VENTINTAKE VENT PROJECTION LENS3.LAMP MODULE COVER 6.ADJUSTABLE FEETFigure 2-2. LS-7Rear/Bottom/Top View 1.RUNCO LOGO BADGE 2.REAR COVER1.HDMI 1 Digital HDMI 2 Digital 5.COMPONENT 1/SCART RCA connectors2.2 LS-7Rear Panel Figure 2-3. LS-7Rear Panel9.TRIGGER 2 3.5-mm,mini phono jack 2.3 LS-7Remote Control7.S-VIDEO 8.IR INPUT5.Aspect Ratio Selection Button 7.Memory Preset Buttons M1 / M2 / M38.Picture Adjustment Buttons Contrast Sharpness SHARP Press to adjust sharpnessNotes on Batteries 3. Installation3.1 Remote Control Notes on Remote ControlInstallation Figure 3-1.IR Reception Angles90.0 Table 3-1.Installation Overview 3.2 Quick SetupInstallation Considerations InstallationTable 3-2.Projector Installation Options Installation TypeEstimating Throw Distance Ambient LightThrow Distance Figure 3-2.Estimating Throw DistanceVertical and Horizontal Floor InstallationFigure 3-3.Projector Placement Table 3-3.Throw Ratios for the LS-7SeriesFigure 3-4.Vertical Lens Shift Example Only Lens ShiftInstallation Figure 3-5.Horizontal Lens Shift Example OnlyFigure 3-6.Folded Optics Adjusting the Projection3.4 Mounting the LS-7 Folded Optics3.5 Connections to the LS-7 Figure 3-7.HDMI/DVI Source Connections Connecting SourceComponents to the LS-7 HDMI/DVI Connections See FigureFigure 3-8.RGB Connections Y Pb Pr Y Pb Pr DTV Set-TopBox or Other Component YPbPr SourceFigure 3-9.Component Video Connections InstallationInstallation Figure 3-10.Composite and S-VideoConnectionsDVD Player, VCR Satellite Receiver Laser Disc etc Figure 3-11. RS-232Control System Connection to Automation/ Control System or PCRS-232Controller ConnectionTheater Equipment Connecting 12-VoltConnecting an External IR Trigger Output to ExternalConnecting to AC Power 3.6 Turning on the Power 3.7 Lens AdjustmentsFocus Zoom Lens Shift Installation 3.8 Changing the OSD Languageshift exceeds 50 per cent of the screen height Rear Projection Ceiling Mode 3.9 Adjusting the Picture OrientationInstallation 4.3 Selecting An Input Source 4. Operation4.1 Selecting Video Memory 4.2 Selecting an Aspect Ratioseparated by their display modes 4.4 Using Picture-In-PicturePIP4.5 Using the On-ScreenMenus Figure 4-1. LS-7OSD Menu Structure ServiceMain AdvancedFigure 4-2. LS-7Main Menu MainTable 4-2.Aspect Ratio Settings Operation Table 4-2.Aspect Ratio Settings continuedOperation Table 4-2.Aspect Ratio Settings continuedAspect Note sub-menu You must enter a passcode to access the Save ISFBelow Black Above Black Operation Operation Figure 4-6.Overscan Examples Operation Figure 4-7. Source Select Sub-MenuFigure 4-8. LS-7 Advanced Menu AdvancedStandard for your region Table 4-3.x/y Color Gamut Values Offset settings reduce the image brightness Figure 4-9. RGB Adjust Sub-MenuOperation Figure 4-10. Fine Sync Sub-MenuOperation Figure 4-11. LS-7 System Menu SystemFigure 4-12. Source Enable Sub-Menu DMD Area Figure 4-13.PIP and PBP areas for 720p DisplayPBP1 PBP2Operation Figure 4-14.PIP Split-ScreenModeFigure 4-15. LS-7 Control Menu ControlTrigger 2 operates identically to Trigger Operation LanguageFigure 4-16. LS-7 Service Menu Lamp Hours User Memory 1 / User Memory ISF Day ENTEROperation 5.1 Lamp Replacement 5. Maintenance and TroubleshootingTable 5-1.Troubleshooting Chart 5.2 Troubleshooting TipsMaintenance and Troubleshooting Maintenance and Troubleshooting Table 5-1.Troubleshooting Chart continuedMaintenance and Troubleshooting 6. Serial Communications 6.1 RS-232Connection and Port ConfigurationSerial Command Syntax Key CommandsTable 6-1.Serial Command Key Names and IR Codes gam.crt Precede operation and command with a space op operation command CRThe command type can be one of 5 functions Table 6-2.Serial Commands Table 6-2.Serial Commands continued source.sel Table 6-2.Serial Commands continuedccont Table 6-2.Serial Commands continuedblank.screen Table 6-2.Serial Commands continuedact.source Table 6-2.Serial Commands continuedstatus Table 6-2.Serial Commands continuedDescription Table 6-3. RS-232Error CodesError Code LED IndicationSpecifications 7. SpecificationsLS-7Specifications Table 7-1. LS-7SpecificationsSpecifications Table 7-1. LS-7Specifications continuedSpecifications Table 7-1. LS-7Specifications continuedGeneral 100 7.2 LS-7DimensionsFigure 7-1. LS-7Dimensions Specifications7.3 Supported Timings Table 7-2.Supported Signal Timings by InputSpecifications PAL-60 SpecificationsPAL-B/G PAL-MPage 020-1038-00Rev. A December