Manuals / Runco / Computer Equipment / Projector

Runco VX-4000ci manual Install New Lens Assembly

Models: VX-4000ci

1 44

Page 33

Step 5: Remove the Lens and Motor Assembly by pulling forward and to the left in order to clear the Projector chassis with the Motor Assembly.

Figure 4

Install New Lens Assembly

Step 6: Install new Lens Assembly in reverse order. Make sure to route the wire harness (Item 4) in original position and away from moving lens stages and Motor Assembly to prevent unexpected disconnect or lens damage. --See Figure 6 Below--

Figure 5

VX-4000ci Projector (front view) with Lens Assembly completely removed.

Figure 6

Page 33

Image 33

Runco VX-4000ci manual Install New Lens Assembly

Contents

OWNER’S OPERATING MANUAL DHD ControllerVX-4000ci Projector Page Table of Contents Page Features Included AccessoriesIntroduction Warnings and Safety Precautions PRODUCT DISPOSALINFORMATION READ BEFORE USING THE PRODUCT SAFETY TIPSDeclaration of Conformity INTELLECTUAL PROPERTY RIGHTSLIMITED WARRANTY Limited WarrantyWHAT IS COVERED UNDER THE TERMS OF THIS WARRANTY WHAT IS NOT COVERED UNDER THE TERMS OF THIS WARRANTYIMPORTANT WARRANTY REGISTRATION EFFECTIVE WARRANTY DATETO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER ADDITIONAL INFORMATIONFeatures and Benefits Projector Description Top ViewInput Panel Front View Ceiling Mount DimensionsSide View Bottom ViewVertical Lens Shift Up or Down Horizontal Vertical and Lens ShiftHorizontal Lens Shift Left or Right Screen Center 0%Lens Option 1 Throw Distance 1.2 - 1.4 x Width of Screen Lens Shift RangeLens Option 2 Throw Distance 1.4 - 1.77 x Width of Screen ExplanationLens Option 4 Throw Distance 2.35 - 3.60 x Width of Screen Lens Option 3 Throw Distance 1.77 - 2.35 x Width of ScreenExplanation Example 56 x 100 Screen TD = 177 to 235 lens to screenLens Option 6 Throw Distance 0.67 Fixed x Width of Screen Lens Option 5 Throw Distance 3.60 - 5.70 x Width of ScreenExplanation Example 56 x 100 Screen TD = 360 to 570 lens to screenLens Adjustments Zoom / Focus / Shift Page Hard Buttons ProntoNeo Remote Control DescriptionChange function depending on the device you are operating To activate the Device Overview3. Replace the back cover Battery Installation and ReplacementMain Screen ProntoNeo Remote Control UsageSource Screen Menu ScreenFront Panel DHD Controller DescriptionOUTPUTS Rear PanelINPUTS 1. ANALOG OUTPUTS BNC ConnectorsConnection Examples Quick Set-up GuideVX-4000ci Projector DHD ControllerPROJECTOR CONFIGURATION ISF CalibrationDIGITAL INPUTS Overall Functional Description Menu Description and Navigation Opening ScreenInput Source Aspect Ratio PicturePicture yellow whitecyan greenIndicates selection has been made for the ISF Presets selection menu ISF PresetsISF Presets Input PositionLens Replacement Procedure 2 @ 6 oclock Install New Lens Assembly PROBLEM Basic Troubleshooting TipsSOLUTION after initial installation. Theback on after it was powered and the power LED on theThe image appears too washed out, or the darkestGeneral Information RS-232 CommunicationsNOTE A carriage return must be used after each command or string Bits No Parity All protocol in ASCII formatCOMMAND RS-232 CommandsPARAMETER min/max Value stored?PARAMETER min/max COMMANDValue stored? DESCRIPTIONLens Dimensions VX-4000ci Projector DimensionsLens Factor Lens DiameterDHD Controller Dimensions Top PanelFront Panel Native Resolution SpecificationsPower Requirements DimensionsOutput resolution Supplied AccessoriesService Labor and Parts DHD ControllerPage RUMA-010130 8-6-04