STOPPING INSTRUCTIONS

STARTING/STOPPING INSTRUCTIONS

STOPPING INSTRUCTIONS

2. To stop the engine, put the Start/Stop Engine

1. Release your hand from the throttle control (Fig. 23).

Control in the STOP [O] position (Fig. 21).

 

Allow the engine to idle.

 

OPERATING INSTRUCTIONS

OPERATING THE CLICK-LINK®SYSTEM

The Click-Link®system enables the use of these optional add-ons.

Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . BV720r

2.While firmly holding the add-on, push it straight into the Click-Link®coupler (Fig. 25).

NOTE: Aligning the release button with the guide recess will help installation (Fig. 24).

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . HS720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . SS725r

Sweeper/Blower . . . . . . . . . . . . . . . . . . . . . . . . . SB720r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

Click-Link®Coupler

Release Button

Primary Hole

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

WARNING: Read and understand operator’s manual for add-on prior to operation.

Removing the Cutting Attachment or Add-Ons:

1.Turn the knob counterclockwise to loosen (Fig. 24).

2.Press and hold the release button (Fig. 24).

3.While firmly holding the upper shaft housing, pull the

cutting attachment or add-on straight out of the Click-Link®coupler (Fig. 25).

Installing the Cutting Attachment or Add-Ons:

WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing add-ons.

NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench.

1. Turn knob counterclockwise to loosen (Fig.24).

Click-Link® Coupler

Release Button

 

Knob OPERATING INSTRUCTIONS

Guide Recess

Fig. 24

Upper Shaft Housing

Lower Shaft Housing

Fig. 25

3. Turn the knob clockwise to tighten (Fig. 26).

CAUTION: Lock the release button in the primary hole and securely tighten the knob before operating this unit.

90˚ Edging Hole

OPERATING THE CLICK-LINK®SYSTEMRemoving the Cutting Attachment or Add-Ons: 180˚ Edging Hole

Installing the Cutting Attachment or Add-Ons:Manual background Knob

Fig. 26

CAUTION: The cutting attachment and add-ons with the Click-Link® system are to be used in the primary hole unless stated otherwise in the specific add-ons operator’s manual. Using the wrong hole could lead to personal injury, or damage to the unit.

For edging when using the line head cutting attachment with Click-Link® models, lock the release button of the cutting attachment into the 90° edging hole or the 180° edging hole(Fig. 26).

WARNING: Do not use the cutting blade for edging or as an edger, severe personal injury to yourself or others can occur.

15

Page 15
Image 15
Ryobi 890r manual Operating Instructions, Operating The Click-Link System, Starting/Stopping Instructions