Blades, Speed and Wiring | Ryobi BT3100-1 guide

FEATURES

BLADES

It is recommended that you use only the RYOBI 10 in. (254 mm) Combination Blade, which is for use with the BT3100 Table Saw. You will get maximum performance with the following features:

•	36 precision ground, micro-grain carbide teeth	• laser-cut expansion slots
•	kerf width of 2.5 mm + .02	• tensioning for 4,800 rpm

This blade is provided with the saw. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local RYOBI dealer can provide you with complete information.

CAUTION:

Be sure to use only blades that are rated for at least 5,500 RPM and recommended for use on this saw.

PRECISION GROUND

MICRO-GRAIN

CARBIDE TEETH

LASER-CUT BODY

AND EXPANSION SLOTS

BLADE ROTATION

Fig. 7

SPEED AND WIRING

The no-load speed of your table saw is approximately 4,800 rpm. The speed will not remain constant but will be less under a load. The wiring in a shop is as important as the motor's horsepower rating. A line intended for lights only

WILL NOT PROPERLY CARRY A POWER TOOL MOTOR. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools.

WARNING:

To prevent possible electrical hazards, have a qualified electrician check the line if you are not certain that it is properly wired.

Page 14

Image 14

Ryobi BT3100-1 manual Blades, Speed and Wiring

Contents

Operators Manual Save this Manual for Future Reference Table of Contents Product Specifications Symbol Meaning Rules for Safe Operation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFF Safety and International Symbols Electrical Connection ElectricalExtension Cords Grounding Instructions Glossary of Terms In. NUT Driver UnpackingTools Needed Socket Wrench Loose Parts List Key Description Quan Following items are included with your table saw leg stand E J Sliding FeaturesGetting to Know Your SAW Scale Power Switch Operating Components Speed and Wiring Blades Assembly Assembling LEG Stand Mounting the LEG Stand on the Table SAW Base To Install Front and Back RailsAssembling Storage Brackets Handwheel To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter Hole B Lever To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate FIT LIP of Table Into Rear Rail Small HEX Wrench To Check SAW Blade InstallationTo Install Blade Guard Assembly Throat Plate Replacing the Throat Plate Screws Operation Types of Cuts Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard Locking Lever Left Lever Right Rotate Blade AdjustingTo Remove the Blade Inch Blade Guard Riving KnifeRiving Knife Blade Riving Knife Mounting Plate To SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle To Lock Miter Table Adjustingmiter Clampfence Quick StopNever use rip fence as cutoff gauge when crosscutting To Make a Straight Cross CUT To Make a Straight RIP CUT Adjusting ClampTo Make a Miter CUT Miter Table Blade Rear Rail RIP Fence To Make a Bevel Cross CUT To Make a Bevel RIP CUT To Make a Large Panel CUT Accessory Miter Locking Clamps Rail ClampTo Make a Compound Miter CUT Clamp Push Block Bevel To Make NON-THROUGH CutsFeatherboard Operation Backup Washer MaintenanceGeneral Maintenance Lubrication Screws Lock NUT To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop Bolt Lock SET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps Screw SET Front Rail Miter Locking Clamp To Adjust the Sliding Miter Table Assembly To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table Spring Plate Backup HEX NUT Checking Sliding Miter Table Assembly To Check Miter Base Parallelism Making Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base B Miter Indicator To Adjust the Miter FenceTo Adjust QUICK-STOP LIP of Base Trouble Shooting Problem Cause Solution Ryobi Authorized Service CenterPage 111 102 105 117 116 114 115 Refer to Figure112 107 8283 108 113 101 110 104 122 Parts List Figure See Back page for Ordering Instructions Parts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description Quan Ryobi 10 in mm Table SAW Model NO. BT3100-1 Parts List for Figure KEY Description Quan Operators Manual 10 in mm Table Saw Model BT3100-1 Ryobi TECHNOLOGIES, INC