![](/images/new-backgrounds/1283572/2835723x1.webp)
TABLE OF CONTENTS
■ Product Specifications | 2 |
■ Rules for Safe Operation | |
■ Electrical | 7 |
■ Glossary of Terms For Woodworking | 8 |
■ Unpacking and Tools Needed | 9 |
■ Loose Parts List | |
■ Features | |
Operating Components | 13 |
Power Switch | 13 |
Turn Your Saw On | 13 |
To Turn Your Saw Off | 13 |
To Lock Your Saw Switch | 13 |
Blades | 14 |
■ Assembly | |
Assembly Leg Stand | 15 |
Assembly Storage Brackets | 16 |
Mounting Leg Stand to the Table Saw Base | 16 |
To Install Front and Back Rails | |
To Install Miter Table and Fence | 17 |
To Install Accessory Table and Rip Fence | 18 |
Removing/Replacing the Throat Plate | 18 |
Blade and Guard Assembly | 19 |
To Check Saw Blade Installation | 20 |
To Install Blade Guard Assembly | 20 |
■ Operation | |
Basic Operation | 21 |
Causes of Kickback and Avoiding Kickback | 21 |
Cutting Aids | 21 |
Types of Cuts | 22 |
Featherboard | 23 |
How To Make a Featherboard | 23 |
How To Mount a Featherboard | 23 |
Settings And Adjustments | |
To Remove The Blade | 24 |
To Check, Replace or Adjust The Riving Knife |
|
and Blade Guard Assembly | 25 |
To Adjust the Blade Depth | 26 |
To Adjust the Blade Angle | 26 |
To Set the Scale to the Blade | 26 |
To Lock the Miter Table | 27 |
Making Cuts | |
To Make a Straight Cross Cut | 27 |
To Make a Miter Cut | 28 |
To Make a Straight Rip Cut | 28 |
To Make a Bevel Cross Cut | 29 |
To Make a Bevel Rip Cut | 29 |
To Make a Compound Miter Cut | 30 |
To Make a Large Panel Cut | 30 |
To Make | 31 |
To Make Dado Cuts | 32 |
■ Maintenance | |
General Maintenance | 33 |
Lubrication |
|
Locker Bracket Assembly | 33 |
Tilt / Elevating Mechanism | 33 |
To Set Blade to 0 or 45 Degrees | 34 |
To Check Alignment of the Rip Fence to |
|
the Blade | |
To Adjust the Bevel Locking Lever | 35 |
To Align the Miter Locking Clamps | 35 |
To Adjust the Front and Rear Rail Clamps | 36 |
To Adjust the Accessory Table | 36 |
To Adjust the Sliding Miter Table Assembly | 36 |
Checking Sliding Miter Table Assembly | |
Making Adjustments to Sliding Miter Fence Table |
|
Assembly | |
■ Troubleshooting | |
■ Exploded View and Parts List | |
■ Parts Ordering / Service | 52 |
PRODUCT SPECIFICATIONS
Blade Diameter |
| 10 in. (254 mm) |
Blade Arbor |
| 5/8 in. (16 mm) |
|
|
|
Cutting Depth at 0° |
| |
|
|
|
Cutting Depth at 45° |
| |
|
| |
Rating | 120 Volts, 60 | |
|
|
|
Output Speed |
| 4,800 RPM |
|
| |
Net Weight Without Workstand | 75 lbs. (34.1 kg.) | |
|
| |
Net Weight With Workstand | 107 lbs. (48.6 kg.) |
Page 2