Unpacking, Tools Needed, In. NUT Driver, With 7/16 | Ryobi BT3100-1

UNPACKING

Your Model BT3100-1 Table Saw is shipped complete in one carton and includes two table extensions, a rip fence, a miter fence with adjusting clamp, a blade guard, rails, and leg stand.

Separate all parts from packing materials and check each one with the illustration and the list of Loose Parts to make sure all items are accounted for, before discarding any packing material.

If any parts are missing, do not attempt to assemble the table saw, plug in the power cord, or turn the switch on until the missing parts are obtained and are installed correctly. Call 1-800-525-2579 for assistance if any parts are missing or damaged.

The saw is factory set for accurate cutting. After assem- bling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in the opera- tion and maintenance sections of this manual.

WARNING:

If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

TOOLS NEEDED

	3/8 in. NUT DRIVER	3/4 in.
	3/8 in. NUT DRIVER	WRENCH
		WRENCH

SOCKET WRENCH

WITH 7/16 in.

SOCKETADJUSTABLE

WRENCH

#2 PHILLIPS

SCREWDRIVER

FLAT BLADE

SCREWDRIVER

FRAMING SQUARE

COMBINATION

SQUARE

Fig. 2

Page 9

Image 9

Ryobi BT3100-1 manual Unpacking, Tools Needed, In. NUT Driver, Socket Wrench, With 7/16

Contents

Save this Manual for Future Reference Operators Manual Product Specifications Table of Contents Rules for Safe Operation Symbol Meaning Read ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are Secure Safety and International Symbols Extension Cords ElectricalElectrical Connection Grounding Instructions Glossary of Terms Tools Needed UnpackingIn. NUT Driver Socket Wrench Key Description Quan Loose Parts List E J Following items are included with your table saw leg stand Getting to Know Your SAW FeaturesSliding Scale Operating Components Power Switch Blades Speed and Wiring Assembling LEG Stand Assembly To Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole B REMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear Rail To Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat Plate Replacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Lever Right Rotate Blade Adjusting To Remove the BladeLocking Lever Left Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting Plate To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade Never use rip fence as cutoff gauge when crosscutting Adjustingmiter Clampfence Quick StopTo Lock Miter Table To Make a Straight Cross CUT To Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP Fence To Make a Bevel RIP CUT To Make a Bevel Cross CUT Accessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel Operation General Maintenance MaintenanceBackup Washer Lubrication To Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt Lock To Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking Clamp To Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUT To Check Miter Base Parallelism Checking Sliding Miter Table Assembly Eight screws are visible on the miter base B Making Adjustments to Sliding Miter Table Assembly To Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of Base Problem Cause Solution Trouble Shooting Center Ryobi Authorized ServicePage Refer to Figure 112 107 8283 108 113 101 110 104 122111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List Figure Parts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard Assembly Ryobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for Figure Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1