Ryobi BT3100-1 - page 48

Page 48

RYOBI 10 in. (254 mm) TABLE SAW - MODEL NO. BT3100-1

FIGURE 61: MOTOR ASSEMBLY

Key

No. Description Quan.

1Arbor........................................................... 1

2Woodruff Key (3/16 in.) ..............................1

3Ball Bearing (6003)..................................... 1

4Bearing Plate.............................................. 1

5Arbor Pulley................................................ 1

6Retaining Ring............................................ 1

7Ball Bearing (6002)..................................... 1

8Ball Bearing (6200ZZ) ................................1

9Motor Bracket .............................................1

10 Motor Pulley ............................................... 1

11 Armature Assembly.................................... 1

12 Bearing Bushing .........................................1

Key

No. Description Quan.

13 Screw and Washer (Field Pan Hd.)............ 2

14 Field Assembly ......................................... 1

15 Motor Housing .......................................... 1

16 Brush Cover.............................................. 2

17 Brush Assembly........................................ 2

18 Brush Holder Assembly ............................2

19 Screw and Washer (Pan Hd.)................... 4

20 Set Screw (Hex)........................................ 2

21 Strain Relief Bushing ................................1

22 Cable Clamp .............................................1

23 Power Cord............................................... 1

24 Connector .................................................2

1

24

3567

9

8

10 11

12

13

13

14

24

15

16

17

18 19

20 19

16

17

18 19

20

21

22

23

Contents

Main TABLE OF CONTENTS PRODUCT SPECIFICATIONS IMPORTANT DANGER: WARNING: CAUTION: READ ALL INSTRUCTIONS Page SAVE THESE INSTRUCTIONS SAFETY AND INTERNATIONAL SYMBOLS SYMBOL MEANING NO HANDS SYMBOL ELECTRICAL ELECTRICAL CONNECTION Figure 1. GROUNDING INSTRUCTIONS EXTENSION CORDS GLOSSARY OF TERMS UNPACKING TOOLS NEEDED LOOSE PARTS LIST The following items are included with your table saw leg stand. LOOSE PARTS LIST GETTING TO KNOW YOUR SAW OPERATING COMPONENTS POWER SWITCH WARNING: BLADES SPEED AND WIRING ASSEMBLING LEG STAND See Figures 8 and 9. ASSEMBLING STORAGE BRACKETS See Figure 9. MOUNTING THE LEG STAND ON THE TABLE SAW BASE See Figure 10. TO INSTALL FRONT AND BACK RAILS TO INSTALL MITER TABLE AND FENCE See Figures13 and 14. See Figure 13. See Figure 14. TO INSTALL ACCESSORY TABLE AND RIP FENCE REMOVING/REPLACING THE THROAT PLATE See Figure 16. BLADE AND GUARD ASSEMBLY TO CHECK SAW BLADE INSTALLATION Figures 16 and 17. Operation TO INSTALL BLADE GUARD ASSEMBLY Operations CUTTING AIDS BASIC OPERATION OF THE TABLE SAW Electrical CAUSES OF KICKBACK AVOIDING KICKBACK TYPES OF CUTS FEATHERBOARD HOW TO MAKE A FEATHERBOARD See Figure 24. HOW TO MOUNT A FEATHERBOARD SETTINGS AND ADJUSTMENTS TO REMOVE THE BLADE See Figures 25 - 27. See Figure 26. TO CHECK, REPLACE OR ADJUST THE RIVING KNIFE AND BLADE GUARD ASSEMBLY Figure 29. See Figure 30. TO ADJUST THE BLADE DEPTH See Figure 31. TO ADJUST THE BLADE ANGLE See Figure 32. TO SET THE SCALE TO THE BLADE MAKING CUTS TO MAKE A STRAIGHT CROSS CUT See Figure 35. TO MAKE A MITER CUT See Figure 37. TO MAKE A STRAIGHT RIP CUT See Figure 38. TO MAKE A BEVEL CROSS CUT See Figure 39. TO MAKE A BEVEL RIP CUT See Figure 40. TO MAKE A COMPOUND MITER CUT TO MAKE A LARGE PANEL CUT See Figure 41. TO MAKE NON-THROUGH CUTS See Figure 42. See page 25. TO MAKE DADO CUTS GENERAL MAINTENANCE LUBRICATION LOCKER BRACKET ASSEMBLY See Figure 43. TILT /ELEVATING MECHANISM TO SET BLADE AT 0 OR 45 See Figure 45. Figure 45, insert. See Figure 45, insert. TO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADE TO ADJUST THE BEVEL LOCKING LEVER See Figure 47. TO ALIGN THE MITER LOCKING CLAMPS See Figure 48. TO ADJUST THE FRONT AND REAR RAIL CLAMPS See Figure 49. TO ADJUST THE ACCESSORY TABLE See Figure 50. TO ADJUST THE SLIDING MITER TABLE ASSEMBLY CHECKING SLIDING MITER TABLE ASSEMBLY To Check Miter Base Parallelism: See Figure 52. To Check Miter Fence Alignment See Figure 53. MAKING ADJUSTMENTS TO SLIDING MITER TABLE ASSEMBLY To Adjust the Miter Base See Figure 54. TO ADJUST THE MITER FENCE See Figure 55. TO ADJUST QUICK-STOP See Figure 57. PROBLEM CAUSE SOLUTION TROUBLE SHOOTING PROBLEM CAUSE SOLUTION Page Page 43 FIGURE 58: 10 in. (254 mm) TABLE SAW FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 59 FOR RIP FENCE ASSEMBLY, REFER TO FIGURE 60 FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE 62 FOR MOTOR ASSEMBLY, REFER TO FIGURE 61 SEE BACK PAGE FOR ORDERING INSTRUCTIONS PARTS LIST - FIGURE 58 PARTS LIST - FIGURE 58 (CONT'D) FIGURE 59: SLIDING MITER TABLE ASSEMBLY FIGURE 60: RIP FENCE ASSEMBLY Page FIGURE 63: REPLACEMENT PARTS FIGURE 62: BLADE GUARD ASSEMBLY Page RYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100-1 PARTS LIST FOR FIGURE 64 OPERATOR'S MANUAL 10 in. (254 mm) Table Saw Model BT3100-1 SERVICE MODEL NO. EXTENSION CORD CAUTION