OPERATION

WARNING:

Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

APPLICATIONS

This product has been designed only for the purposes listed below:

nCrosscutting wood and plastic (do not cut metals, ceram- ics or masonry products.)

nCrosscutting miters, joints, etc. for picture frames mold- ings, door casings, and fine joinery

nBevel cutting and compound cutting

NOTE: The blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from the dealer.

NOTE: Always check for interference between the blade and the sliding miter fence BEFORE attempting to make a cut. Some compound miter cuts require the sliding miter fence to be moved or completely removed before making the cut.

CUTTING WITH YOUR COMPOUND MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury.

TO MITER CROSS CUT/STRAIGHT CROSS- CUT

See Figures 32 - 33.

A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the 0° position. Miter crosscuts are made with the miter table set at some angle other than zero.

nPull out the lock pin and lift saw arm to its full height.

nLoosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

nPress the miter lock plate down with thumb and hold.

nRotate the control arm until the pointer aligns with the desired angle on the miter scale.

WARNING:

Before starting any cutting operation, clamp or bolt the compound miter saw to a workbench. Never operate the miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.

WARNING:

To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

WARNING:

To avoid serious personal injury, keep hands outside the no hands zone, at least 3 in. from the blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

WORK

CLAMP

Fig. 32

23

Page 22 Page 24
Page 23
Image 23
Ryobi TS1552DXL manual Operation, Applications, To Miter Cross CUT/STRAIGHT CROSS- CUT, See Figures 32
Page 22 Page 24

TS1552DXL specifications

The Ryobi TS1552DXL is a highly regarded table saw designed to meet the needs of both DIY enthusiasts and professional carpenters. With a powerful 15-amp motor, this table saw is capable of handling a wide range of cutting tasks, from simple crosscuts to intricate bevel cuts with precision and ease.

One of the standout features of the TS1552DXL is its large 15-inch maximum rip capacity. This allows users to cut larger sheets of material, making it an ideal choice for those working with plywood or large boards. The saw’s adjustable cutting depths and an included miter gauge provide additional versatility, enabling users to make accurate crosscuts and angled cuts up to 60 degrees.

The Ryobi TS1552DXL is equipped with a foldable stand that enhances stability and portability. This convenient feature allows users to set up and store the saw easily, so it can be moved from one job site to another without hassle. The saw also incorporates a heavy-duty steel frame that not only ensures durability but also provides excellent support when working with larger materials.

Safety is a top priority with the Ryobi TS1552DXL. The saw comes with a blade guard that offers protection during operation while maintaining visibility of the cutting area. Additionally, the built-in push stick and safety switch further enhance user safety, making it a great choice for both seasoned professionals and those new to woodworking.

In terms of technology, the Ryobi TS1552DXL features a rack and pinion system for smooth adjustments. This system allows for quick and easy modifications to the blade height and angle, enabling users to achieve precise cuts consistently. The powerful motor, when combined with a high-quality carbide-tipped blade, delivers clean and efficient cuts, reducing the need for excessive sanding or finishing.

Overall, the Ryobi TS1552DXL boasts a range of features, reliable performance, and user-friendly technologies that make it a standout choice in the world of table saws. Whether you are working on small projects at home or tackling larger jobs on the worksite, this saw offers the reliability and precision needed to get the job done efficiently.
Top Page Image Contents