ADJUSTMENTS
SQUARING THE SAW BLADE TO THE FENCE
See Figures 17 - 20.
■ Pull the saw arm all the way down and engage the lock |
pin to hold the saw arm in transport position. |
■ Loosen the miter lock handle approximately |
turn. |
■ Depress the miter lock plate and rotate the miter |
table until the pointer on the control arm is positioned |
at 0° . |
■ Release the miter lock plate and securely tighten the |
miter lock handle. |
■ Lay a framing square flat on the miter table. Place one |
leg of the square against the fence. Slide the other leg |
of the square against the flat part of saw blade. |
NOTE: Make sure that the square contacts the flat part |
of the saw blade, not the blade teeth. |
■ The edge of the square and the saw blade should be |
parallel as shown in figure 17. |
■ If the front or back edge of the saw blade angles away |
from the square as shown in figures 18 and 19, adjust- |
ments are needed. |
■ Using the 8 mm hex key (allen wrench) provided, loosen |
the socket head screws that secure the mounting |
bracket to the miter table. See Figure 20. |
■ Rotate the mounting bracket left or right until the saw |
FENCE
|
|
|
| 45˚ |
|
|
|
|
| ˚ |
|
|
|
|
| 40 |
|
|
|
|
| ˚ |
|
|
|
|
| 0 |
|
|
|
|
| 3 |
|
|
|
|
| ˚ |
|
|
|
| 0 |
| |
|
|
| 2 |
|
|
|
|
| ˚ |
|
|
45˚ | 40˚ |
| 10 |
|
|
30˚ | 20˚ |
|
| ||
|
|
|
| ||
|
|
|
| BLADE |
|
MITER |
|
|
|
|
|
TABLE | FRAMING |
|
| ||
|
|
|
| ||
|
| SQUARE |
|
| |
VIEW OF BLADE NOT SQUARE WITH |
| ||||
FENCE, ADJUSTMENTS ARE REQUIRED | Fig. 18 | ||||
|
|
|
|
| |
FENCE |
|
|
|
|
|
45˚
40˚
30˚
20˚
45˚ | 40˚ |
| 10˚ | |
30˚ | 20˚ | |||
|
|
blade is parallel with the square. |
■ Retighten the screws securely and recheck the blade- |
FENCE
MITER TABLE
BLADE
FRAMING
SQUARE
|
|
|
| 4 | 5 | ˚ |
|
|
|
|
| ||
|
|
| ˚ |
|
|
|
|
|
| 40 |
|
|
|
|
|
| 30˚ |
|
|
|
|
|
| 20˚ |
|
|
|
45˚ | 40˚ |
| 10˚ |
|
|
|
30˚ | 20˚ |
|
|
| ||
|
|
|
| |||
|
|
|
|
| ||
|
|
|
| BLADE | ||
MITER |
|
|
|
|
| MITER |
|
|
|
|
| LOCK PLATE | |
TABLE |
| FRAMING |
|
|
| |
|
|
|
|
| ||
|
|
| SQUARE |
|
| MITER |
|
|
|
|
|
| |
CORRECT VIEW OF |
|
| LOCK HANDLE | |||
BLADE SQUARE WITH FENCE |
|
| Fig. 17 | |||
VIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED
45
0 15
8 mm SOCKET | 30 |
| |
HEAD SCREW(S) | 45 |
Fig. 19
Page 16
8 mm HEX KEY | MOUNTING | MITER |
| TABLE | |
| BRACKET | Fig. 20 |
|
|
