ASSEMBLY
MOUNTING SAFETY SHIELDS
See Figures 6.
Mount the left and right shield rods to the inside of the wheel guards using the clamp brackets, hex bolts (8 mm x 14 mm), and washers (8 mm).
Use the illustration as a guide to determine which shield rod is mounted on the left and which shield rod is mounted on the right of the grinder.
Once shield rods are firmly in place, slide the shield bracket onto the shield rod. Tighten the carriage bolt leaving it loose enough to allow the safety shield to be raised and lowered easily.
WORK REST
See Figure 7.
Before attempting to mount the work rest, remove the hex nut and star washer from the phillips screw. Place the work rest over the phillips screw before replacing the hex nut and star washer. Using the hex bolt (5 mm x 10 mm) and washer (5 mm), secure the work rest against the inside of the wheel guard.
Before tightening the bolts, adjust the gap between the grinding wheel and the work rest to a maximum of 1/16 in. (1.6 mm). Tighten securely
SHIELD ROD
CLAMP BRACKET |
WASHER |
HEX BOLT |
|
|
|
|
|
|
| Grinder | ||
8” | Bench |
|
| ||||||
|
|
|
|
|
|
|
| ||
|
| ING |
|
|
|
|
|
| |
| RN |
| NT |
|
|
|
|
|
|
WA SSEME |
|
|
| 48467 | 43F1 |
|
| ||
AVERTI | CIA |
|
|
|
| ||||
ADVE | RTEN |
|
|
|
| E |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 0N |
| |
F |
|
|
|
|
|
|
|
|
|
0F |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Y |
|
|
|
|
|
|
|
| A | |
|
|
|
|
|
|
| R |
| |
|
|
|
|
|
|
| TT |
|
|
|
|
|
|
|
| N |
|
| |
|
|
|
|
| A |
|
|
| |
|
|
|
| L |
|
|
|
| |
|
| O |
|
|
|
|
| ||
O |
|
|
|
|
|
|
| ||
C |
|
|
|
|
|
|
|
|
|
Fig. 6
|
|
|
| Grinder |
8” | Bench | |||
|
|
| ||
WARN | ING |
|
| |
|
|
| ||
AVERTISSEMENTCA | 48467 | 43F1 | ||
ADVE | RTEN |
| E |
|
|
|
|
| |
|
|
|
| 0N |
0FF
|
|
|
|
| Y |
|
|
|
| A | |
|
|
| R |
| |
|
|
| TT |
|
|
|
| N |
|
| |
| A |
|
|
| |
L |
|
|
|
| |
O |
|
|
|
|
|
O |
|
|
|
|
|
C |
|
|
|
|
|
PHILLIPS
SCREW
WORK
REST
STAR
WASHER
HEX BOLT | HEX NUT | |
WASHER | ||
|
Fig. 7
Page 10
