Manuals / Brands / Household Appliance / Air Conditioner / Samsung / Household Appliance / Air Conditioner

Samsung AR10NVFSCURNSV Remote Control Operation, Dry, Mode, Mode, Cool, humidity, Glance a At, Operation modes, Indoor temperature, pressing the button, Temperature control

1 45

Download 45 pages, 0 b

Glance a At

Remote Control Operation

You can use the air conditioner easily by selecting a mode and then by controlling the temperature, fan speed, and air direction.

Operation modes

You can change the current mode between Auto, Cool, Dry and Fan by

pressing the button.

Controlling temperature

You can control the temperature in each mode as follows:

Mode	Temperature control

Auto/Cool	Adjust by1 °C between 16 °C and 30 °C.

Dry	Adjust by1 °C between 18 °C and 30 °C.

Fan	You cannot control the temperature.

NOTE

You can use the Cool and Dry modes in the following conditions:

Mode	Cool	Dry

Indoor temperature	16 °C to 32 °C	18 °C to 32 °C

Outdoor temperature	16 °C to 46°C	16 °C to 46 °C

Indoor humidity	80% or less relative	_
Indoor humidity	humidity	_
	humidity

•If the air conditioner operates in a high humidity environment in the Cool mode for an extended period of time, condensation may occur.

10English

Contents

AR**NVFH Contents Safety Information At a Glance Power Smart Features Energy-SavingFeatures Indoor Unit Installation Step 2.1 Connecting the power and communication cables (assembly cable) Step 2.2 Optional: Extending the power cable Step 2.3 Installing and connecting the drain hose Step 2.4 Optional: Extending the drain hose Safety Information Install your appliance on a level and hard floor that can support its weight Install the drain hose properly so that water drains correctly FOR POWER SUPPLY When the circuit breaker is damaged, contact your nearest service centre • Failing to do so may result in electric shock or fire •Do not use a ventilating fan •A spark may result in an explosion or fire To reinstall the air conditioner, please contact your nearest service centre •This may result in electric shock •If a child places a bag over its head, it may result in suffocation Do not touch the air flow blade with your hands or fingers during heating •This may result in electric shock or burns Do not strike or pull the air conditionerwith excessive force •The water may be harmful to humans •This may result in burns or injury •This may result in property damage •This may result in harm to humans, animals or plants FOR CLEANING Indoor Unit Overview Remote Control Overview Remote Control Operation Vertical air flow Features Smart Power Cooling Operation Dehumidifying Operation Quick Smart Features Fast function Comfort function Quiet function Beep sound function Energy-SavingOperation Features Saving-Energy Timed on/Timed off function good’sleep function (Select among On, Off, and .) (Set the operation time.) ► Cleaning at a Glance Maintenance and Cleaning Cleaningand Maintenance Troubleshooting Page Installation Power supply line, fuse, or circuit breaker Preparation Step1.1 Choosing the installation location Overview of installation location requirements •Comply with the length and height limits described in the figure above Minimum clearances for the outdoor unit Step1.3 Checking and preparing accessories and tools Optional accessories Accessories in the outdoor unit package Tools General tools •Vacuum pump Step1.4 Drilling a hole through the wall Indoor Unit Installation •Tighten the terminal block screw to 1.2-1.8N•m (1.2-1.8kgf•cm) •Each wire is labelled with the corresponding terminal number •Use shield cable (Category 5; less than 50pF/m) for noisy environmental site •Power & Communication cable shall not exceed Step 2.2 Optional: Extending the power cable 1Prepare the following tools •Peel off 20 mm of cable shields from the pre-installedtube • The compression dimension should be Three or more layers of insulation are required •In case of extending the electric wire, please DO NOT use a round-shaped pressing socket or a fire Step 2.3 Installing and connecting the drain hose 1Install the drain hose Step 2.5 Optional: Changing the direction of the drain hose Cut out the appropriate 2Smooth the cut edges 4Cut off the remaining foam insulation •The pipe should not project from the rear of the indoor unit 6Pass the pipe through the hole in the wall Step 2.8 Fixing the installation plate You can install the indoor unit on a wall, window frame, or gypsum board When fixing the indoor unit on a wall Tighten the flare nut at the specified torque. If the flare nut is When fixing the indoor unit on a window frame 1Use stud finder to find out locations of the studs 2Fix the plate hanger on two studs •Fix the installation plate without inclining to one side Outdoor Unit Installation Step 3.1 Fixing the outdoor unit in place Step 3.3 Evacuating the air of cooling capacity and malfunction. Use a vacuum pump •When installing, make sure there is no leakage 1Leave the system in the standby mode 3Open the valve of the low pressure side of manifold gauge anticlockwise •Close the valve of the low pressure side of manifold gauge clockwise •Turn off the vacuum pump •Check for 2 minutes if there is any pressure change •Remove the hose of the low pressure side of manifold gauge Installation Inspection ❈: Off, : Blinking, : On Step 4.3 Performing final check and trial operation 1Check the following: •Strength of the installation site •Tightness of pipe connection to detect gas leak •Electric wiring connection Page Page QUESTIONS OR COMMENTS DB68-07847A-00

Remote Control Operation

Operation modes

You can change the current mode between Auto, Cool, Dry and Fan by

pressing the button.

Controlling temperature

You can control the temperature in each mode as follows:

Mode

Temperature control

Adjust by1 °C between 16 °C and 30 °C.

Adjust by1 °C between 18 °C and 30 °C.

You cannot control the temperature.

You can use the Cool and Dry modes in the following conditions:

Cool

Dry

Indoor temperature

Outdoor temperature

humidity