Installation Inspection | Samsung AR18NVPXCWK/MG instruction

Installation Inspection

Step 4.1 Performing the gas leak tests

1Before inspecting the leakage, use a torque wrench to close the cap for the stop valve. (Comply with a tightening torque for each size of the diameter, and tighten the cap firmly to prevent any leakage.)

Tightening torque for body cap (Refer to the table)

Charging core

Spindle

R-22: Thread of the screw - 7/16-2OUNF

R-410A: Thread of the screw -1/2-2OUNF

Tightening torque for charging port cap (Refer to the table)

Outer diameter	Tightening torque
(mm)	Body cap (N•m)	Charging port cap (N•m)
	Body cap (N•m)	Charging port cap (N•m)

ø 6.35	20 to 25

ø 9.52	20 to 25

ø 12.70	25 to 30	10 to 12

ø 15.88	30 to 35

Over ø 19.05	35 to 40

( 1 N•m = 10 kgf•cm )

2Insert inert gas into the pipes connected to indoor and outdoor units.

3Test leakage on the connection parts of the indoor and outdoor units with soap lather or liquid.

Test parts for the indoor unit

Test parts for the indoor unit

Step 4.2 Running the Smart Install mode

1Make sure that the air conditioner is in the standby status.

2Hold down the (Power), (Mode), and

(SET / Temperature type (℃↔℉)) buttons on the remote control simultaneously for 4 seconds.

3Wait until Smart Install mode succeeds or fails. It takes approximately 7 to 13 minutes.

• While Smart Install mode is proceeding:

	Type	Display	LED Display
			LED1
			LED2
			LED3
	Indoor
	unit	The progress is	The LEDs on the
	indicator		The LEDs on the
	indicator		indoor unit display
		displayed as a	blink in sequence,
		number between	blink in sequence,
		number between	then all of them
		0 and 99 on	then all of them
		0 and 99 on	blink simultaneously.
		the indoor unit	blink simultaneously.
		the indoor unit	These operations
		display.	These operations
		display.	repeat.
			repeat.

•When Smart Install mode succeeds: Smart Install mode ends with ringing sound, and the air conditioner is in standby status.

•When Smart Install mode fails: An error message is displayed on the indoor unit display, and Smart Install mode ends.

NOTE

•Smart Install mode can be operated only with the supplied remote control.

•During the Smart install mode procedure, remote control cannot be operated.

Installation

English 51

Image 51

Samsung AR18NVPXCWK/MG manual Installation Inspection, Running the Smart Install mode, Performing the gas leak tests

Contents

Airconditioner Contents Correct disposal of batteries in this product This may result in electric shock or fire Failing to do so may result in electric shock or fire For Power Supply This may result in children seriously injuring themselves Do not touch the circuit breakerwith wet handsThis may result in electric shock This may result in electric shock or burns Do not touch the pipes connected with the product Do not place objects or devices under the indoor unitDo not operate the appliance with wet hands Do not drink the water from the air conditioner Do not clean the inside of the air conditioner by yourself For Cleaning Room temperature sensor Inside Ionizer Indoor Unit OverviewDisplay Inserting batteries Remote Control Overview Remote Control Operation Controlling temperatureOperation modes Controlling air flow direction Controlling fan speed Comfortable Cool modeCooling Operation Step cooling function Wind-Free Cooling function Ionizer function Dry modeDehumidifying Operation Air Purifying Operation Fast function Quick Smart FeaturesAuto mode Fan mode Comfort function Beep sound functionSelect Beep Display lighting function Quiet function Wi-Fi function Samsung Connect App Operation Select Usage Energy-Saving OperationElectricity consumption check Single userfunction Timed on/Timed off function Good’sleep function Cool mode Method Running Auto cleanTo deactivate the Auto clean function To cancel the Auto clean operation Cleaning the filter Resetting the filter-cleaning reminderDo not clean the display by using alkaline detergent With your hand Tip on cleaning the Wind-Free panelGently push the air flow blade Hold and pull both sides Gently push the air flow blade Problem Solution Troubleshooting Sure to pass the error code to the service centre Indicator blinksCheck whether the drains are clean. Clean them regularly An error is indicated 35˚C Technical Specifications27˚C 19˚C Downloading the Samsung Connect app Connecting networkConnecting the wireless IP routerwith an air conditioner This Wi-Fi Aircon support only below three encryption Registering your air conditioner to the Samsung Connect app SpecificationsRegistering Samsung account Log in with a Samsung account Controlling the air conditionerwith Samsung Connect App Open Source Announcement Troubleshooting General information Safety Information on Installation Install the unit in a place where water can drain smoothly Power supply line, fuse, or circuit breaker Cases Choosing the installation locationPreparation Minimum clearances for the outdoor unit Outdoor unit Packing and UnpackingUnit mm Indoor unit Accessories Accessories in the indoor unit packageOptional accessories Tools for test operation Accessories in the outdoor unit packageDrilling a hole through the wall Tools General tools Taping the pipes, cables, and drain hose Remove the cap screws, then the screws Indoor Unit InstallationInstallation plate Disassembling the cover panel Connecting the Power and communication cables assembly cable Optional Extending the power cable Fire Installing and connecting the drain hoseInstall the drain hose Optional Extending the drain hose Optional Changing the direction of the drain hose Each pipe when facing the wall Pass the pipe through the hole in the wall Shortening or extending the refrigerant pipes assembly pipe 10 Fixing the installation plate When fixing the indoor unit on a wallWhen fixing the indoor unit on a window frame 12 Assembling the cover panel 11 Fixing the indoor unit to the installation plateWhen fixing the indoor unit on a gypsum board Fix the installation plate without inclining to one side Optional Fixing the outdoor unit to a wall with a rack Outdoor Unit InstallationFixing the outdoor unit in place Refrigerant pipes Cooling capacity and malfunction. Use a vacuum pump Evacuating the air Siphon Adding refrigerant Installation Inspection Running the Smart Install modePerforming the gas leak tests Blocking error Open Error betweenPower cable or communication Motor Connector Remove foreign substance. Check Disconnect the pipes Check the following Strength of the installation sitePerforming final check and trial operation Pumping down for removing the product Questions or COMMENTS?