Check the followings | Samsung AS24VBFNUMG, AS18VBFNUMG instruction

FinalAA Check and Trial Operation

To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly.

Check the followings:

•Strength of the installation site

•Tightness of pipe connection to detect gas leak

•Electric wiring connection

•Heat-resistant insulation of the pipe

•Drainage

•Grounding conductor connection

•Correct operation (follow the steps below)

1.Press the Power button and check the following:

The indicator on the indoor unit lights up.

The airflow blade opens and the fan gears up for operation.

ENGLISH

2.Press the Mode button to select Cool mode.

 In Cool mode, use Temp + or - button and set the temperature at 16°C.

• Approximately 3~5 minutes later, outdoor unit will start to operate and the Cool air will blow out.

• After 12 minutes of stationary condition check the indoor unit air treatment:

Cooling mode (indoor unit check)  Inlet air temp. - Outlet air temp : From 10°K to 12°K ( indicative delta T)

3. Press the Air swing button and check the following:

 The airflow blades work properly.

4.Press the Power button to stop the operation.

• When you complete the installation successfully, hand over this manual to the user for storage in a handy and safe

place.

Pump down procedure (when removing the product)

1.Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes.

2. Release the valve caps on High and Low pressure side.

3. Use L wrench to close the valve on the high pressure side.

4. Approximately 2 minutes after, close the valve on the low pressure side.

5. Stop operation of the air conditioner.

6. Disconnect the pipes.

41

UMG_AQ&AS18V@_IBIM_34038A_E--P14�P18��.indd 41

2013-3-18 11:00:20

Image 41

Samsung AS24VBFNUMG, AS18VBFNUMG manual Check the followings, Press the Mode button to select Cool mode

Contents

English Contents Important safety symbols and precautions SafetAA y precautionsFollow directions Wall socket For Using For Cleaning Operation ranges ChecAA king before use Set temperature Mode indicator Auto clean indicatorMode indicator Room temperature ChecAA king the name of the parts Remote controller buttons ChecAA king the remote controller Battery changing time Remote controller displayStoring the remote controller Inserting the batteries BasicAA function Press the button to set the desired fan speed Press the button to adjust the temperature Press the Air swing button on the remote controller Using the Turbo functionAdjusA ting the air flow direction Vertical air flow Press the button on the remote controller AA modePress the Set/Cancel button to active it on Set Off timer Press the On Timer/Off Timer button to set the time SettinAA g the On/Off timerPress the On Timer/Off Timer button Turn off automatically From the moment you have set the timerIf the air conditioner is on If the air conditioner is off Using the dlight Cool function Using the Smart Saver function Using the Virus Doctor function Using the Quiet function UsingAA the Auto Clean functionWhen the air conditioner is turned on Runs Cleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchanger Removing the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated area Close the front panel Deodorizing and Bio filter Periodical checks MainAA taining the air conditioner TroubAA leshooting Connection TroubleshootingFlow movement changes. It is normal General information Safety precautions Installing the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easily Model Where sulfide gas existsOutdoor Unit When installing more than 1 outdoor unit ChoosingAA the installation locationWhen the air outlet is towards the wall  Figure Description Accessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operations Connecting the cable Connecting the assembly cableCable specification Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessary Cut off the remaining foam insulation Smooth the cut edges Cutting or extending the pipe PurgiAA ng the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flare Outer Diameter Drain hose installation Changing direction of the drain hose AQseries Purging the connected pipesConnect a drain hose to the drain plug Ensure that condensation draining is adequate If you use a pipe shorter than 4 or 5m Gas service port as seen in the pictureAdding Refrigerant Fixing the indoor unit in place PerfoAA rming the gas leak tests FixinAA g the outdoor unit in place Outdoor unit installed on the wall by rack Press the Power button to stop the operation Press the Mode button to select Cool modeCheck the followings Press the Air swing button and check the following Apply heat to the contraction tube to contract it AAHow to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finish AQ18VBFUMG AQ24VBFUMG TechnAA ical Specifications Questions or COMMENTS? Air Conditioner