Samsung HC-P4363W Memorizing the Channels

TV OPERATION

26

1

Press the MENUbutton.

Press the …or †button to

select “Channel”, then press the

ENTERbutton.

2

Press the …or †button to

select “Air/CATV”, then press the

ENTERbutton.

Press the …or †button to

select “Air”, “STD”, “HRC” or

“IRC”, then press the ENTER

button.

Press the EXITbutton to exit.

œIf you are connected to an

antenna, press the …or †button

to select “Air”.

œIf you connected cable, press

the …or †button to select the

type of cable system: “STD”,

“HRC” or “IRC”.

•“STD”, “HRC” and “IRC” identify various types of cable TV systems. Contact your local cable company

to identify the type of cable system that exists in your particular area. At this point the signal source

has been selected. Proceed to “Storing Channels in Memory Automatically”.

•Subscription cable services require service-specific requirement for viewing.

Antenna : Ant.1 √√

Air/CATV : Air √√

Auto Program √√

Favorite Channels √√

Fine Tune √√

Add/Delete √√

†More

Move Enter Return

Channel

T V

Antenna : Ant.1 √√

Air/CATV :Air √√

Auto Program √√

Favorite Channels √√

Fine Tune √√

Add/Delete √√

†More

Move Enter Return

Channel

T V

Air

STD

HRC

IRC

Selecting the Video Signal Source

Before your TV can begin memorizing the available channels, you must specify the type of

signal source that is connected to the TV (i.e., an antenna or a cable system).

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and

cable channels. After the available channels are memorized, use the CH and CH buttons

to scan through the channels. This eliminates the need to change channels by entering the

channel digits.

BP68-00342A-00Eng_TV 3/30/04 8:51 PM Page 26

Contents

Main Important Warranty Information Regarding Television Format Viewing C Chapter 1: Your New TV Chapter 2: Installation Chapter 3: TV Operation C Chapter 3: TV Operation List of Features Chapter One Accessories Familiarizing Yourself with Your New TV Control Buttons Page Connection Jacks (Rear) Page Page Connecting VHF and UHF Antennas Chapter Two Antennas with 300-ohm Flat Twin Leads Antennas with 75-ohm Round Leads Separate VHF and UHF Antennas Connecting Cable TV If you want to connect cable, and you do not need to use a cable box: Page Connecting a VCR Also, you can connect to AV 3 on the side panel of TV. Connecting a Second VCR to Record from the TV Connecting a DVD Player Also, you can connect to AV 3 on the side panel of TV. Connecting to Regular Audio and Video Jacks Connecting a Digital TV Set-Top Box Page Connecting a Camcorder Connecting to the Digital Audio Input Installing Batteries in the Remote Control Connecting Additional Speakers The rear panel jacks on your TV make it easy to take advantage of the surround sound system. Turning the TV On and Off Chapter Three Plug & Play Feature Plug & Play feature doesnt work when the V-Chip is activated or when in the A/V mode. For details, see page 27. For details, see page 52. Viewing the Menus and On-Screen Displays Selecting a Menu Language Selecting the Antenna Input You can connect two different signal sources by choosing the antenna input (Ant.1 or Ant.2). Adjusting the Screen Automatically (Self Focus) Deactivating the Automatic Execution of the Self Focus Removing the Self Focus Message from the Display Memorizing the Channels Storing Channels in Memory Automatically Changing Channels Adding and Erasing Channels To add channels that were not memorized (or to delete unwanted channels from memory): To Store Your Favorite Channels: Selecting Your Favorite Channels Only memorized channels can be set as Favorite channels. To View Your Favorite Channels: Labeling the Channels If you add or delete the TV channel, the labeled channels list will also be added or deleted. Scanning the Channels The TV automatically scan all of the channels it has memorized. When the ANT 2 IN mode is selected, the channel scan function works on the main picture only. Fine Tuning Channels Using Automatic Picture Settings Customizing the Picture Selecting the Color Tone Changing the Picture Size Digital Noise Reduction Viewing Picture-In-Picture Activating the PIP Page Changing the Location of the Sub picture Selecting a Signal Source for the Sub picture After you set the signal source (antenna or cable) of sub picture, it is easy to change channels. Freezing the Picture Using the MUTE Button At any time, you can temporarily cut off the sound by using the MUTE button. Adjusting the Volume Using Automatic Sound Settings Customizing the Sound The sound settings can be adjusted to suit your personal preference. Choosing a Multi-Channel Sound (MTS) track Auto Volume Setting the Dolby Digital Converts and outputs mono and stereo audio signals into a 5.1 channel surround sound audio signal. Setting the Dynamic Range This function only works when Dolby Digital is activated. Adjusting Speaker Levels The Test Tone for the sub woofer is very low frequency. This is normal, not a malfunction. Adjusting the Time Delay for Surround Sound Speakers Selecting a Digital Audio Source Setting the Clock Manually Setting the Clock Automatically The Clock can be set automatically if you are receiving a digital signal. continued... Certain broadcasts may not transmit the correct time. In this case, set the time manually. Page Setting the Sleep Timer The sleep timer automatically shuts off the TV after a preset time (from 30 to 180 minutes). Setting the On/Off Timer Setting the Blue Screen Mode Viewing Closed Caption Information The Caption function doesnt operate when the PIP is active. Setting the On/Off Melody A melody sound can be set to come on when the TV is powered On or Off. Using the V-Chip (USA) How to Change Your Password How to Enable/Disable the Rating Controls Page How to Set up Restrictions Using the MPAA Rating Explanation of the MPAA and TV (FCC) Rating Systems: Viewing an External Signal Source BP68-00342A-00Eng_TV 3/30/04 8:51 PM Page 66 Press the or button to select Edit Name, then press the ENTER button. Press the MENUbutton. Press the ENTERbutton to select Input. Assigning Names to External Sources This feature enables you to name the input source you have connected. Customizing Your Remote Control Page Chapter Four Page Using the Search and Skip Functions Using the Play Function When Playing a MP3/WMA Page When Playing a MPG When Playing a JPEG If you want to return to the file list, press the (Stop) button. Using the Disc Menu Using the Title Menu Displaying the Disc Information Using the Zoom Function (DVD/VCD) Changing the Camera Angle When a DVD contains multiple angles of a particular scene, you can select the Angle function. Using the Bookmark Function (DVD/VCD) Repeat Play Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc. Depending on the disc, this function may not work. Program Play (CD) Setting up the Language for Player Menu Setting up the Display Options Setting up the Parental Control If you have lost your password, enter the master password (1369). To cancel the rating level, select No in the Use Password by pressing the button. T Chapter Five Identifying Problems T A Cleaning and Maintaining Your TV Using Your TV in Another Country Specifications