Spinpoint P120S series
200.0/250.0GB
Capacity1 | 200GB | 250GB |
Model | SP2004C | SP2504C |
• 125GB Formatted Capacity Per Disk |
• Serial ATA 3.0Gbps Interface Support |
• SATA Native Command Queuing Feature set |
DRIVE CONFIGURATION
Interface | Serial ATA 3.0 Gbps |
|
|
Buffer DRAM Size2 | 8 MB |
|
|
Bytes per Sector | 512 |
|
|
PERFORMANCE SPECIFICATIONS |
|
|
|
Read Seek Time (typ.) |
|
|
|
0.8 ms | |
|
|
8.9 ms | |
|
|
18 ms | |
|
|
4.17 ms | |
|
|
7,200 rpm | |
|
|
Data Transfer Rate |
|
|
|
973 MB/sec | |
|
|
300 MB/sec | |
|
|
7 sec | |
|
|
RELIABILITY SPECIFICATIONS |
|
|
|
1 sector in 1014 bits | |
|
|
MTBF | 600,000 POH |
|
|
Start/Stop Cycles (Ambient) | 50,000 |
|
|
Component Design Life | 5 years |
|
|
ENVIRONMENTAL SPECIFICATIONS
Temperature
0 ~ 60 ºC | |
|
|
20 ºC/hr | |
| |
Humidity | |
|
|
5 ~ 90 % | |
|
|
5 ~ 95 % | |
| |
Linear Shock (1/2 sine pulse) | |
|
|
63G | |
|
|
350G | |
| |
Vibration (swept sine, 1 octave per minute) | |
|
|
Operating |
|
5 ~ 21 Hz | 0.034” (double amplitude) |
21 ~ 300 Hz | 1.5 |
|
|
| |
5 ~ 21 Hz | 0.195” (double amplitude) |
21 ~ 500 Hz | 8 |
| |
Altitude (relative to sea level) | |
|
|
|
|
|
|
POWER REQUIREMENTS
• Device Initiated SATA Power Management |
• Staggered |
• High Speed Dual Digital Signal Processor (DSP) Based |
Architecture |
• ATA S.M.A.R.T. Compliant |
• ATA Automatic Acoustic Management Feature Set |
• ATA |
ACOUSTICS (AVERAGE SOUND POWER)
2.5 Bel | |
|
|
2.8 Bel | |
|
|
*Notes:Design and specifications are subject to change without prior notice
Voltage | +5V±5%,+12V±10% |
Spin Up Current (max.) | 650 / 1900 mA |
|
|
Seek (typ.)3 | 9.5 W |
|
|
Read/Write | 8.5 W |
|
|
Idle (typ.) | 7.5 W |
|
|
Standby (typ.) | 0.7/1.5 W4 |
|
|
Sleep (typ.) | 0.7/1.5 W4 |
|
|
PHYSICAL DIMENSION
• ATA Streaming Feature Set |
• ATA Device Configuration Overlay Feature Set |
• NoiseGuard™ |
• SilentSeek™ |
Height | 1 in |
Width | 4 in |
|
|
Depth | 5.75 in |
|
|
Weight | 1.4 lb |
|
|
1.1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes
*Accessible capacity may vary as some OS uses binary numbering system for reported capacity
2.Upper 128 KB is used for firmware
3.30% duty cycle, random seek
4.Power consumption with / without slumber mode