Connecting Wireless Rear Speakers
| 1 Connect your pair of | 2 Insert the power plug into an outlet, |
| wireless rear speakers, | and then press the POWER button |
| (L) and (R), to the | on the front panel. |
Caution 
• Do not connect the wireless rear speakers |
to the speaker outputs on the back of the |
Resetting Wireless Communication
Reset the system if a communication failure occurs, or if the synchronizing signal indicator does not light up and the "REAR CHK" message blinks on the main unit's display.
Reset the system while the main unit and the wireless rear amplifier
| wireless rear amplifier. | • The Power Standby indicator will light up. | |
|
| • To turn off the wireless rear amplifier, |
|
| press the POWER button in Standby mode. |
Wireless Rear Speaker (L) | Wireless Rear Speaker (R) | |
main unit. Malfunction may result. |
• The wireless receiving antenna is built into |
the wireless rear amplifier. |
Keep the unit away from water and |
moisture. |
• For optimal listening performance, make |
sure that the area around the proposed |
wireless rear amplifier location is clear of |
any obstructions. |
1 With the main unit turned off, press and hold the remote control's WIRELESS button for 4 seconds.
•Press the button until the volume control indicator lights up blue. (The indicator will turn off in 1 second.)
2 With the wireless rear amplifier turned on, use a ball point pen or a pair of tweezers to press the RESET button on the back of the unit 2 to 3 times.
RESET Button
Back of Wireless Rear Amplifier
CONNECTIONS
Back of Wireless Rear Amplifier
3 Turn on the main unit.
• The wireless rear amplifier's synchronizing signal indicator will light up.
• If Power Standby mode continues, repeat Steps 1 to 3 above.
Caution 
• Sound will be heard from the wireless rear speakers in |
DVD |
• In |
When using the wireless transmission antenna
Stand the wireless transmission antenna to face upward for best communication status.
Caution 
• Do not apply a strong shock to the wireless transmission antenna. Breakage may result. |
• Do not touch the wireless transmission antenna during operation. Noise or interference to communications may result. |
Note |
• Place the wireless rear amplifier at the rear of the listening position. If the wireless rear amplifier is too close to the main unit, some sound |
interruption may be heard due to interference. |
• If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same frequency |
(2.4GHz) near the system, some sound interruption may be heard due to interference. |
• The transmission distance of radio wave is about 33 feet but may vary depending on your operating environment. If a |
metallic wall is between the main unit and the wireless rear amplifier, the system may not operate at all because the radio wave cannot |
penetrate metal. |
13
rear speakers. |
Turning On the Mood Light
You can turn the mood light on the wireless rear amplifier on or off, as well as change the light to one of 7 different colors according to your preference.
1 Press the POWER button on | 2 | Press the COLOR MODE button. |
the wireless amplifier. |
| • Each time the button is pressed, the color changes as |
• The Power Standby indicator on the |
| follows: Blue ➞ Light Green ➞ Red ➞ Sky Blue ➞ |
front panel will light up and the |
| Yellow ➞ Pink ➞ White. |
mood light will turn on.
Turning Off the Mood Light
• In Power Standby mode, press the ON/OFF button on the Wireless amp.
The mood light will light up or turn off with the last color selected.
Turning off the Wireless Amp and Mood Light
• Press the POWER button on the wireless amp.
The wireless rear amplifier and the mood light will turn off. | 14 | |
When the wireless amp is powered on again, the mood light will be blue. | ||
|
