Setting up Your PC Software Windows only | Samsung PS-50P4H1

Setting up Your PC Software (Windows only)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

2

3

4

5

1Right click the mouse on the Windows Desktop, then click on Properties. The Display Dialog-Boxwill be displayed.

2Click on Settings, then set the Display Mode with reference to the Display Modes Table. You do not need to change the Colours settings.

3Click on Advanced. A new settings dialog box will be displayed.

4Click on the Monitor tab, then set the Screen Refresh Rate with reference to the Display Modes Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen Refresh Rate.

5Press the OK button, close the window, then press the OK button on the Display Registration Information window. Automatic re-booting may commence at this moment.

6Shutdown the PC, and connect it to your TV. (See page 57)

➢◆ The actual screens on your PC may look different, depending on your particular version of Windows and the type of your PC.

◆When you use your TV as a PC monitor, it supports Colours up to 32 bits.

◆In this case, the display on the TV may look different depending on your particular version of Windows or the PC manufacturer.

◆When connecting a PC (including the DVI connection), you must set it to the display settings that are supported by the TV.

Otherwise, the message Out of input range will be displayed.

English - 62

Image 62

Samsung PS-50P4H1 manual Setting up Your PC Software Windows only

Contents

PDP-TELEVISION User Instructions Checking Parts Contents Symbols Contents Your New Plasma Display Panel Front Panel Side of the TV Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-Base Installing the Display on the Wall Attachment Panel Installation Notes Connecting External Devices to the PDP Using a Coaxial cable Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDP Switching On and Off Placing in Standby Mode Change channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu system Setting Up Your Remote Control VCR Plug & Play Feature To start the search, press the Enter button If you want to reset this feature Choosing Your Language Storing Channels Automatically BG DK I L Storing ChannelsManuallyAuto PAL Secam or Channel mode Skipping Unwanted Channels Skipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the Child Lock Activating the child lock Dynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Colour Tone Cool2, Cool1, Normal, Warm1, or Warm2 Adjusting the Picture SettingsBrightness, or Sharpness Adjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3 Setting the Picture PC Mode Setting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Viewing the Channel Scan Picture Freezing the Current Picture Selecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode White enhancement Selecting the Film ModeDNIeTM Digital Natural Image engine Setting the My Colour Control Easy Control Setting the My Colour Control Detail Control Setting the Blue Screen Setting the Melody Sound Using the Colour Weakness Enhancement Feature Viewing the Picture In Picture PIP Video2 Component1 Component2 PC DVI Easy functions of remote control Component1, Component2, PC, or DVI Operates or stops the TV’s internal Fan Using the Digital NR Noise Reduction FeatureSelecting the Fan Pixel Shift selected Protecting the Screen BurningYou can prevent the residual image of the PDP Changing the Sound Standard Standard Music Movie Speech Custom Adjusting the Sound Settings Adjusting the Volume Automatically Setting the TruSurround XT Selecting the Internal Mute Selecting the Sound Mode depending on the model DUAL- I ↔ Dual Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Auto Power Off Satellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceAV1, AV2, AV3, S-Video1,S-Video2,Component1 Redirecting an Input to the External Output … or † button Press the Enter button to confirm the change Teletext Feature Displaying the Teletext Information Selecting Display Options To display Press Selecting a Teletext Rear of the TV Connecting to the External DevicesInput/Output Specification Connecting to the S-Video Input Rear of the TV Side of the TV Connecting to the DVI Input Connecting to the PC Input Connecting to the Component Input Rear of the TV Connecting and Using the Home Theater System Connecting the Home Theater System How to Install Speakers Parts How to Assemble the SpeakersWall Mount Setting up Your PC Software Windows only Input Mode PC/DVI FrequencyHz Pin Configurations Troubleshooting Before Contacting Service Personnel Programming the Remote Control for Other Components JVC Programming the Remote Control for Other Components NEC After Sales Service