Samsung SCC-643AP, SCC-643P Camera SET Menu, Camera ID, Color/Bw, Sync, Means there are Sub Menus

1. CAMERA SET MENU

CAMERA ID

The CAMERA ID menu assigns an ID to the SCC-643(P) to be displayed on the connected monitor.On the CAMERA SET menu screen, select CAMERA ID to ON and press [Enter]. You will see the sub screen for deciding on the ID of the SCC-643(P). The Camera ID can have up to 12 alphanumeric characters, along with several special characters.

COLOR/BW

In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.

In low light conditions, IR Filter is turned OFF to the BW Mode and the sensitivity to low light increases to that of a black and white camera. In bright light conditions, the IR Filter is turned ON to the COLOR Mode, and the screen changes to normal as the sensitivity decreases.

COLOR : The IR Filter is ON and the screen is normal.

BW : The IR Filter is OFF and the screen is black and white.

(CAMERA SET)
CAMERA ID	OFF
V-SYNC	INT
COLOR/BW	AUTO...
ZOOM SPEED	3
MOTION DET	OFF
EXIT	QUIT

The assigned camera ID may be positioned to any desired location on the screen by using the LOCATION submenu.

(Sensitivity to low light is increased to a level comparable to a black and white camera.)

AUTO : Select to automatically switch between the COLOR mode and BW mode

E

(CAMERA SET)

CAMERA ID	ON...
V-SYNC	INT
COLOR/BW	AUTO...
ZOOM SPEED	3
MOTION DET	OFF
EXIT	QUIT

➜

Press [Enter]

(CAMERA ID)

AB C D E F G H I J K L M N O PQ R S T U V W X

Y Z 0 1 2 3 4 5 6 7 8 9

:! - + ✽ ( ) / SP ï î SP LOCATION...

RET

SCC-643.....

depending on the amount of light. In low light conditions, the IR Filter is turned OFF and the sensitivity to low light is increased by switching to the BW mode, but in

bright light conditions, the IR Filter is turned ON and the sensitivity is decreased by switching to the COLOR mode. If you select AUTO and press the ENTER button, a screen from which you can set the BURST ON / OFF, BW LEVEL and DWELL TIME will appear.

- BURST ON	: The color burst signal is output together with black and white
composite video signal.
- BURST OFF	: The color burst signal is not output.
- LEVEL	: You can set the brightness level that changes from COLOR mode to BW

* " ... " Means there are Sub Menus.

V-SYNC

In the V-SYNC menu, vertical synchronization can be selected. The vertical synchronization signal supported by the SCC-643(P) is the INT mode made by clock inside the SCC-643(P) and LINE mode adjusting vertical synchronization to the exterior power frequency.

(CAMERA SET)
CAMERA ID		OFF
	V-SYNC	INT
COLOR/BW		AUTO...
ZOOM SPEED		3
MOTION DET		OFF
EXIT		QUIT

mode in 3 steps : LOW, MEDIUM, and HIGH.

- DWELL TIME : Set the HOLDING time for switching between COLOR and BW mode depending the changes in the amount of light. You can set the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).

In AUTO mode, AGC will operates in high speed mode, and you cannot change it manually, as it is indicated by "---".

Select LINE and press [Enter]. You will see the LINE LOCK submenu where you can adjust the phase of the LINE LOCK.

You can use the PHASE menu of the LINE LOCK submenu to assign as much PHASE as you want.

(CAMERA SET)
CAMERA ID	OFF	➜
V-SYNC	INT
COLOR/BW	AUTO...	Press
ZOOM SPEED	3
MOTION DET	OFF	[Enter]

(BW SETUP)
	ON
BURST
LEVEL	MEDIUM
DWELL TIME	S------L

(CAMERA SET)
CAMERA ID	OFF
V-SYNC	LINE...

➜

(LINE LOCK)

EXIT QUIT

RET

COLOR/BW	AUTO...
ZOOM SPEED	3
MOTION DET	OFF
EXIT	QUIT

Press [Enter]

PHASE ( 000) ---- I ----

RET

Caution : If you use an infrared light source while in AUTO mode, AUTO switching malfunction and camera AF malfunction may occur.

3-4 3-5