Samsung SCC-C4307P manual Other SET

-C-LEVEL: It is used to set the levels for the Burst signal and the entire colour signal of the video signal.

-OTHER SET

In OTHER SET menu, you can adjust LANGUAGE, CTRL TYPE, ZOOM SPEED, D-ZOON, RS-485, SYSTEM INFO..., and V-SYNC function, etc. When you press [ENTER] key from OTHER SET menu, the OTHER SET additional menu screen appear.

(OTHER SET)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	4
D-ZOOM	OFF
RS-485	...
SYSTEM INFO ...
V-SYNC	INT

RET

Press the

ENTER button.

(RS-485)

PROTOCOL SAMSUNG

BAUD RATE 9600

ADDRESS 0 RET

- SYSTEM INFO : You can confirm settings related to the

(SPECIAL)
POSI/NEGA	+
DIS	OFF
REVERSE	OFF

(OTHER SET)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	4

RS-485 communication, product serial number, and the software version.

E

DETAIL	(0)--I-
Y-LEVEL	(0)I--------
C-LEVEL	(0)I--------
OTHER SET	...

D-ZOOM	OFF
RS-485	...
SYSTEM INFO ...
V-SYNC	INT

(OTHER SET)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	4
D-ZOOM	OFF

Press the

(SYSTEM INFO)

ROM VER	1.000
EEP VER	1.000
PROTOCOL	SAMSUNG

RET RET

❖ V-SYNC menu is only available in SCC-C4307.

RS-485	...
SYSTEM INFO ...
V-SYNC	INT

RET

ENTER button.

ADDRESS	0
TYPE	RS-485, HALF
BAUD RATE	9600
SERIAL NO	000000000000000

RET

- LANGUAGE : Selects English/French/German/Spanish/

Italian OSD menu.

- CTRL TYPE : By inputting the wire remote port, you may

set up the mode, A, B, C, or D.

Code	Item	Tele	Wide	Far	Near
	A	-6V	+6V	+6V	-6V
	B	-6V	+6V	-6V	+6V
	C	+6V	-6V	+6V	-6V
	D	+6V	-6V	-6V	+6V

- ZOOM SPEED : Use [Left, Right] key in the ZOOM SPEED

menu to set the speed as follows.

- ZOOM SPEED 1 : About 17Sec. from X 1 to X 32(Slowest)

-V-SYNC : INT shall be selected to use internal synchronization. LINE... is used to synchronize several camera phases for the multi camera operation by using an external signal(AC signal). As there may be a slight deviation between sets, adjusts PHASE to overcome this handicap. When you use AC power source, V-SYNC is available. Select LINE... and press [ENTER] and the PHASE control submenu will appear. The PHASE control ranges from -106H to +106H as for NTSC and from -138H to +138H as for PAL.

❖When a DC power is supplied, V-SYNC menu will be displayed as --- and you cannot make any settings.

- ZOOM SPEED 2 : About 10Sec. from X 1 to X 32(Slow)

- ZOOM SPEED 3 : About 6Sec. from X 1 to X 32(Fast)

- ZOOM SPEED 4 : About 3Sec. from X 1 to X 32(Fastest)

- D-ZOOM : Sets up the Digital Zoom magnification ratio up

to x10.

- RS-485 : Sets up RS-485 Communication Protocol,

Address, and Baud Rate.

(OTHER SET)
LANGUAGE	ENGLISH
CTRL TYPE	A
ZOOM SPEED	OFF
D-ZOOM	OFF
RS-485	...
SYSTEM INFO ...
V-SYNC	LINE...

RET

Press the

ENTER button.

(LINE LOCK)

PHASE	(-106)----I----
RET

29

30